2006 Dodge Durango Logo

Related Topics:

Posted on Jan 31, 2011
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

How do I remove the battery from a 2006 Dodge Durango?

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

  • Master 430 Answers
  • Posted on Jan 31, 2011
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

Joined: Nov 08, 2010
Answers
430
Questions
3
Helped
231886
Points
1141

One side of that battery will have a single 13 mm bolt that you can loosen and or remove entirely to allow you to remove that battery. Screws located down near the bottom of the battery.
The fender is on the left and then the battery and then the wedge is on the battery side which faces the engine. You need to remove it with a socket and long extension.

Remove the negative battery and place it out of the way then remove the positive cable and move it as well.Remove the heat guard or shield which surrounds the battery if installed.Remove the battery hold down wedge by unscrewing the bolt.Lift out the battery.Reverse for installation.--------------- Thank you.


  • Nick
    Nick Oct 17, 2013

    after replacing the battery in my 206 Dodge Durango. The instrument cluster memory had to be reconfigured

×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Location to remove and replace a starter on a 2006 Dodge Durango

The starter on a 2006 Dodge Durango is located under the vehicle, towards the passenger side. Specifically, it's near the transmission, mounted on the lower side of the engine block.

Note that the exact location might vary slightly based on the specific Durango model and engine type.

Also, be careful when attempting to remove and replace the starter, as it involves dealing with electrical components which can be dangerous if handled improperly.
0helpful
1answer

Starting problems dodge durango 2006

for one, your starter / solonoid unit is in need of attention, even replacement ! it stays engaged, hanging up, solonoid could be going bad, replace the entire unit. check the positive & negative battery cables sometimes they need replaced ! think about it, a cable as big as they are, you would'nt think they would need replaced , but maybe they do ??? just a thought ! alwasy clean battery terminals , put vaseline on them before reconnecting the terminals, it will keep them clean & corrosion free ! clean off battery also, remember its acid, so don't get any on your clothes !
0helpful
1answer

My 2006 dodge durango 2wd v8 would not start wouldn't even turn over has power battery good

CHECK TO SEE IF YOU HAVE POWER TO SMALL WIRE ON STARTER WHILE TRYING TO CRANK IT. IF YOU HAVE POWER, THAN SUSPECT STARTER. TRY TAPPING STARTER WITH HAMMER, THIS SOMETIMES WORKS.
0helpful
1answer

How do I change a battery in 2006 dodge durango

if you have a cover remove it( i personaly would through it away), disconnect the cabels, remove the mount that holds the battery in place, remove the old battery and then reverse all steps only with the new battery
0helpful
1answer

2006 dodge durange wont start tried to recharge

Some times battery's are beon recharging that recharge wont do it, after you recharge battery turn your lights on, if very dim or dont come on, battery is no good replace it, also try to start it it if lights go off, replace battery.
0helpful
1answer

How to I replace a broken tail light assembly?

Open hatch, remove the 2 screws on the side of the broken light, pull firmly and replace.
0helpful
2answers

I have a 2006 dodge Durango and the dash lights

remove cluster. disconnect and reconnect harness. if this fails you will need to replace cluster, as it has internal failure
6helpful
1answer

2006 dodge durango driver side front power seat just stopped working. Where is the fuse located for the power seat/what number is it in the fuse box?

I have a 2006 Dodge Durango. Drivers side power seat has stop working. Want to check the fuse, however unable to remove the fuse. Any suggestions on how to remove the fuse without breaking it?
Not finding what you are looking for?

1,336 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...