I need torque specs for a 2004 chevy aveo front hub. installing new rotors

Front Hub Nut Torque is 160 newton meter = 118 pound foot.

Just tighten hard as you can,I have never torque my brake parts.

Pad material will cause these problems.... Buy good Cermic pads and new rotors and you won't have that problem

Adjustment

The wheel bearings on these vehicles are not adjustable. If the bearings become loose or make noise, they must be replaced.

Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. On 4WD vehicles, remove wheel center cap, if equipped, and the drive axle nut and washer
3. Raise and support the vehicle.
4. Remove or disconnect the following:
   NOTE Lay the hub and bearing on the wheel studs on the outboard side. This will avoid damaging the bearing seal.
   
   
   Tire and wheel Caliper, leaving the fluid lines connected Brake rotor Halfshaft from the hub and bearing on 4WD vehicles. Place a brass drift against the outer edge of the halfshaft to protect the shaft threads. Use a hammer to sharply strike the brass drift, but to do not remove the halfshaft at this time. Wheel speed sensor Wheel hub and bearing-to-steering knuckle bolts and hub and bearing
   
   
   Splash shield from the steering knuckle Seal from the hub and bearing
   

To install:

1. Install or connect the following:
   
   Wheel hub and bearing seal Splash shield to the steering knuckle, making sure it-s properly aligned Hub and bearing to the steering knuckle, aligning the threaded holes Hub and bearing bolts and tighten to 77 ft. lbs. (105 Nm) Wheel speed sensor. Tighten the bolt to 13 ft. lbs. (18 Nm). Rotor and brake caliper Tire and wheel
   The Hub Bearing Torque - Front
   
   If Torque Specs are not in the box we recommend youtorque to this setting. Axle Nut: 103 Ft/Lbs.Flange Bolts: 77 Ft/Lbs. WARNING: Failure to observe the following warningscould create a risk of death or serious injury.Proper maintenance and handling practices arecritical.Always follow installation instructions and maintainproper lubrication.Every reasonable effort has been made to ensure theaccuracy of the information contained in thiswriting, but no liability is accepted for errors,omissions or for any other reason.This information is not intended to substitute forthe specific recommendations of your vehiclemanufacturer.Always use the recommended torque requirement unlessotherwise specified in the carton.Depending on the application, type of hub unitbearing and location, the installation process mayvary.Please review the vehicle manufacturer'srecommendation before removing or installingcomponents.
   
2. Lower the vehicle
3. On 4WD vehicles, install the drive axle nut and tighten to 103 ft. lbs. (140 Nm), then install the center cap.

Here are the front axle nut torque specs for the 2004 Chevy Silverado 2500HD:
• Axle Shaft nut - 177 ft-lb
• hub and bearing assembly to steering knuckle bolts - 133 ft-lb

you can get the torque specs from the dealer. if you replaced the valve cove gasket the just tighten the about the same as you would yor tire by hand not with a power tool!

2WD pickups don't have hubs. They have rotors with bearings. Once you have the brake assembly supported, remove nut from spindle. Be sure not to strip the threads on the spindle. Remove the front set of bearings and pull the rotor off. Remove the rear set of bearings. Be sure to pack greases into new bearings prior to installation. Insert new rear bearing into rotor and replace onto spindle. Insert new front bearing and washer and re-install nut. Tighten to recommended torque specs, grease fittings and replace brake assembly.

18 lb ft+60°+60°+60°+10°

NEW HEAD BOLTS ARE REQUIRED WHEN REPLACING THE HEAD OR HEAD GASKET.

digram at autozone.com

the center bolt for cv axle!103ft-lbs,hub bearing assembly bolts!77ft-lbs