2008 Ford Focus Windshield Washer Fluid level is full but it does not spray on windshield. Had it in for service and they cleared the lines, but it still won't spray on windshield. It cost a lot of money for nothing. What can I check?

Looks like a Body Control Module communication issue.

Windshield Washer
When the washer switch is pulled towards the driver, the SASM sends the washer request to the BCM over the LIN. The BCM activates the windshield wash relay (internal to the BCM) and sends a message to the driver side windshield wiper motor. When the BCM activates the windshield wash relay, voltage is provided to the washer pump, directing washer fluid to the windshield. When the switch is released, the windshield wiper motor continues to activate the windshield wipers for 3 additional wipes and then turns the windshield wipers off.

https://www.justanswer.com/ford/74red-focus-2012-ford-focus-se-need-wiring-diagram-washer-pump.html

..

The hose could be clogged ! Do you know where you add the washer fluid ? Somewhere on the bottom of that plastic bottle is the washer pump .
Removal and Installation
> WARNING: Windshield washer solution contains methanol, which is poisonous. Observe all cautions and warnings indicated on label of washer solution container. Failure to follow these instructions may result in personal injury.
> CAUTION: When replacing the windshield washer pump be careful not to damage the rubber grommet.
> CAUTION: Do not operate the windshield washer pump before filling the reservoir. Failure to do so could result in premature pump failure.

1. NOTE: When installing the reservoir, the filler neck must be lubricated using a water-based lubricant.
   Remove the bolt and the windshield washer reservoir filler neck.

1. Remove the RH fender splash shield. For additional information, refer to Section 501-02 .

1. Remove the foam filler and remove the retainer.

1. Remove the 2 screws and the accessory drive splash shield.
   • To install, tighten to 5 Nm (44 lb-in).

1. Remove the nut, 2 bolts and position the A/C accumulator aside.
   • To install, tighten to 9 Nm (80 lb-in).

1. Unclip the A/C lines from the inner fender well.

1. Drill out the rivet and remove the bracket.

1. Remove the 2 bolts, slide the windshield washer reservoir assembly forward to release it, and position the washer reservoir aside.
   • Install the upper bolt followed by the lower bolt, and tighten to 5 Nm (44 lb-in).

1. Disconnect the windshield washer tube assembly from the pump and release the windshield washer tube assembly from the washer reservoir.

1. Disconnect the electrical connector from the windshield washer pump.

1. Release the wiring harness from the reservoir, and remove the washer reservoir.

1. To install, reverse the removal procedure.

the tube might be disonnected from the fluid tank.

Assuming you have washer fluid and you can hear the pump with no flow at the main line I would guess the turbine has separated from the pump shaft.

Replace the washer pump

Get it at a dealers parts dept

Remove the windshield washer reservoir and give it a good cleaning with a mixture of 1 part bleach and 3 parts water. You may be able to clean it without removing the reservoir by flushing it throughly and the cleaning it while still on the vehicle with the bleach mix. After it is throughly cleaned put a bleach mix in the reservoir and disconnect the hoses from the spray nozzles and run the washer until the hoses are clean. Use a needle to clean out the nozzles, and the connect the hoses and run the washer until the nozzles are clear. Remove the bleach mix and then fill the reservoir with a commercial windshield washer fluid. I recommend Rain X.

follow the windshield spray nasal water lie to the pump making sure the line is not broken, next do you hear the pump running when you spay the fluid, if not that the pump is faulty, if you do hear the pump running, more likely the windshield spray nasal is clog with debris; to unclog it try to use a clothes needle, poke around in it to see if you can clear the blockage, if not, replace will be the best idea, fairly cheap and easy to replace. those windshield tank and the pump does not have good filter on them and they tend to get clog up in the pump or the spray nasal.

If you have used ANYTHING beside windshield solvent in you reservor, you may have created WAXING from soap in the bottom of washer tank, which clogs pump,lines, and nozzel....take the tank out and wash it..disconnect washer hoses at nozzel and clear with compressed air along with the nozzel...if you use solvent only you may have a worn washer pump or restriction...check those and good luck.....

get it down to the gararge to get checked out !!!!

check under your washer reservoir.