At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
https://fuse-box.info > Home > Chrysler
Fuse box diagram (location and assignment of electrical fuses) for Chrysler 300 / 300C (Mk1/LX; 2005, 2006, 2007, 2008, 2009, 2010).
Here is your fuse box diagram Annie, but the blinkers are not in it, because they are controlled by the Body Control Module. (BCM).
If the front is working okay, check the bulb connections, any wire connectors you can see and the wires in that rear area that go to the body for grounding.
You probably going to need a good auto-electrician.
https://fuse-box.info > Home > Chrysler
Fuse box diagrams (location and assignment of electrical fuses and relays) Chrysler. ... fuses) for Chrysler Pacifica (CS; 2004, 2005, 2006, 2007, 2008).
There were 2 directions that I found. Here they are:
With the engine off, turn the ignition switch to "On" without starting the engine.
Within a 10 second interval, push the accelerator pedal all the way down slowly three times within 10 seconds.
Turn the ignition switch to the "LOC" position.
Second one is:
Step 1
Turn the key in your ignition to "ACC." Do not start the engine.
Step 2
Press the "Step" button. This button is located on the instrument panel under the display that tells you how many miles until the car needs to have the oil changed again.
Step 3
Press the "Reset" button until the display shows "3000 Miles to Service."
Turn the key to the "OFF" position and remove it from the ignition. The oil monitoring system has been reset.
Hope this solves your issue.
My 2005 Chrysler Pacifica is shaking still after I took it to a repair shop they fixed the motor mount front left and said that I have to get the engine mount right, left , front and rear, transmission mount engine mount front right. How many mounts are there.
Drive car on ramps or 2 2x12s reach behind oil pan remove bolt drain hot oil from car that has just been driven.into pan. When oil is just dripping very slow say 15 min replace plug. Now just behind front bumper next to engine is an oil filter remove it with an oil filter wrench. Make sure the gasket came off with the filter or just reach up with a clean rag and wipe the housing it will fall off if you touch it. Put oil on gasket of new filter and screw it on when the gasket touches the housing go 3/4 s of a turn more. Put in about 5-1/2 to6 quarts of 10w 30 oil. Start engine for a min ck for leaks shut off and ck dip stick and make sure it reads full after sitting 5 min or so to let oil dip down into pan
Left ( driver's side ) front of the engine on the 5.4L engine.
This is shown to be at the end of the baffled area of the intake, the edge of the pleated area farthest from the airfilter ( looking at the engine, the left side of the pleated folds ). When you locate this, look down the front of the engine.
The connector is a black 1 pin connector with a White w/ Red Stripe wire to it.
You might have to remove the factory air intake plastic housing to see it.
i have tryed that looking for a diagram there is no diagram online the dealerships have not put out a book on market for this vehicale. but keep checking at local auto part dealers
Wrong engine but in same place
×