I have a -00 Dodge Durango and the immobilizer kicked inn. The remote works but the immobilizer wont stop. I have removed the battery (negative) + tryed to turn the key while battery disconected, what to do?

the following is the factory service manual for your car:

http://oskin.ru/pub/chrysler-dodge/manuals/Service%20Manuals/2002_LH_300M_Concorde_Intrepid/02lhe.pdf

goto page 8L- 21

• (1) Open hood and disconnect the negative battery cable remote terminal from the remote battery post.
• (2) Remove the left end cover, left instrument panel trim cover, and the cluster bezel. Refer to the various Removal and Installation procedures in this section.
• (3) Remove the three screws retaining headlamp switch to cluster bezel.
• (4) Remove headlamp switch from bezel.

a youtube of a dodge durango has a similar switch on their dash as well: except for the column shifter

Dodge Durango Stereo Removal 2004-2007 - YouTube

? 3:05
www.youtube.com/watch?v=LEuFEXBZobM
Mar 23, 2013 - Uploaded by Factory Car Stereo Repair Dodge Durango Stereo Removal 2004-2007 .... an amp inside tht if stock radio is removed it will not work unless u connect an adapter tht costs ...
Search Results

images for 2003 dodge durango wiring

vivian check if cables are loose including both terminals. If the battery works on non-rainy days, it could be ok.

IF STARTER RELAY BAD THE STARTER WONT MAKE NO NOISE AT ALL HEADLIGHTS WONT DIM.IF YOU CLICKING NOISE BATTERY VOLTAGE TOO LOW. MAKE SURE BATTERY VOLTS ARE 12.6 VOLTS AND USE TEST LIGHT TO SEE IF STARTER GETTING POWER.COULD HAVE BLOWED IGNITION FUSE OR FAULTY IGNITION SWITCH. TO CHECK STARTER SOLENOID FIRST TURN OFF RADIO THEN REMOVE NEGATIVE BATTERY CABLE AND POSITIVE BATTERY CABLE.THEN REMOVE STARTER BUY A REMOTE SWITCH.YOU NEED BATTERY JUMPER CABLES HOOK BATTERY JUMPER CABLES TO BATTERY PUT POSITIVE CABLE ON POSITIVE BATTERY POST THEN PUT NEGATIVE BATTERY CABLE ON NEGATIVE POST. HOOK BATTERY CABLES TO STARTER USE NEGATIVE CABLE GROUND STARTER BODY AND PUT POSITIVE BATTERY CABLE ON THE LARGE POSITIVE POST ON STARTER SOLENOID. NOW TAKE REMOTE SWITCH HOOK RED WIRE TO STARTER SOLENOID POSITIVE POST THEN HOOK BLACK WIRE TO REMOTE SWITCH TO STARTER SOLENOID SWITCH TERMINAL WITH LETTER S THEN PRESS REMOTE IF STARTER SPINS STRONG WITH A GOOD KICK STARTER GOOD.YOUR PROBLEM COULD BE CORRODED WORN BATTERY CABLES. WEAK BATTERY FAULTY IGNITION SWITCH. IF STARTER DONT WORK WHEN YOU PRESS THE REMOTE SWITCH STARTER SOLNOID BAD OR STARTER ITSELF BAD.IF ALL IS GOOD. CODE SCAN CAR FOR THEFT SECURITY FAULT CODE.

You will have to get it reprogrammed. Check your owner manual.

BCM on the 2001 durango was also known as the CTM but regardless it is located on driver side kick panel where your left foot would be if you are driving. there is two screws to remove panel. its a black box with three plug ins.

please email me answer as soon as possible to [email protected] thankyou

I guess you checked the battery condition but what you are describing can be that 1st. The cables probably need to be removed and scrubbed with a terminal brush (auto parts store). Remove the negative battery first, then the positive (to prevent welding your tools to the car), then clean battery and cables.
If that doesn't cure it, you will have to do the other ends of those same cables.
If you have no dielectric grease, use petroleum jelly liberally on all connections before reattaching them.

try and reset ac by disconecting the negative battery cable and back on againNOTE;;;; check with dodge to make sure u wont loose memory in the ecm before u proceed

You probably need a new brake switch. In addition to turning the brake lights on and off, it also allows you to move out of "park" since you can only shift with your foot on the brake. The switch is up in the drivers footwell and has a button on it that is controlled by the brake pedal itself. Check your fuses before you get a new switch.