Replacing a rear wheel bearing Hub on a 2001 celica 190?

replacing bearing involves removing axle your not replacing a hub but tearing apart axle 99 04 F250 Sterling Rear axle bearing replacement Pt 2 2006 Ford F250 rear hub axle seal replacement F250 Rear Brakes Axle Hub Removal Install 03 07 Powerstroke

Yes , your wheel bearings are bad !!!!!!

32 or 33 mm one of the two should fit

Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical)

1. Release parking brake.
2. Remove rear wheel assembly.
3. Remove rear wheel speed sensor from carrier.
4. Dismount brake caliper and support with mechanic's wire.
5. Remove brake disc.
6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical)
   
   
7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
8. Remove carrier.
9. Remove stakes and remove flange nut.
10. Support bearing outer race flange and press rear axle hub out.
11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.

To Install:
Hub bearing assembly (Typical)

1. Apply thin coat of grease to bearing contact surface and hub.
2. Using and appropriate tool, press bearing into hub. CAUTION
   Do not press against outer race of wheel bearing.
   
3. Install flange nut and stake nut until it meets concave portion of spindle.
4. Install carrier.
5. Use an appropriate tool to press tone wheel.
6. Install hub/bearing assembly with rounded portion of outer race facing up.
7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
8. Measure wheel bearing starting torque with a spring balance or equivalent device.
   • Starting torque should measure 15.9 in lb (1.8 Nm) or less
9. Install brake disc.
10. Mount brake caliper.
11. Install rear wheel speed sensor to carrier.
12. Install rear wheel assembly.

Hi there,

Well to replace the rear wheel bearing it is best to buy the hub with the new bearing pressed in already. The entire assembly runs about $100.00 at any part store. Remove whichever rear wheel you are replacing. The brake line or ABS sensor might be fastened to the rear of the hub so loose that up. Next there are only four bolts the that hold the hub assembly to the control arm. Take those four bolts off and you might need to tab out the hub assembly with a hammer due to rust but spray WD-40 or something similar to help move easier. Hit it from the rear. Don't worry about bang on the ABS sensor exciter ring because the new hub has one on already. Please post comments for further help or information.......

Good Luck!!

2001 Pontiac Grand Am 2.4L SFI DOHC 4cyl

Vehicle Speed Sensor - Location:
The speed sensors are built right into the wheel bearings of your vehicle, at the front and rear locations. They work both with the anti-lock brakes and with the traction control systems on the vehicle.

Removal & Installation
Front
The front wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Front Suspension for service procedures.
Rear
The rear wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Rear Suspension for service procedures.

I hope help you with this (remember rated this help) Have a nice day, good luck.

2001 Pontiac Grand Am 2.4L SFI DOHC 4cyl

Vehicle Speed Sensor - Location:
The speed sensors are built right into the wheel bearings of your vehicle, at the front and rear locations. They work both with the anti-lock brakes and with the traction control systems on the vehicle.

Removal & Installation
Front
The front wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Front Suspension for service procedures.
Rear
The rear wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Rear Suspension for service procedures.

I hope help you with this (remember rated this help) Have a nice day, good luck.

The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

here is how to replace it on a 2 wheel drive please do not forget to rate and comment about your experience today. 2-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake drum
     
   • Wheel hub nut
     
   • Wheel hub
     
   • Inner wheel bearing race from the hub
     
   • Snapring
     
   • Wheel bearing outer race from the knuckle
     
3. 
   

To install:

1. Install or connect the following:
   
   • Wheel bearing in to the knuckle
     
   • Snapring
     
   • Wheel hub into the wheel bearing
     
   • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
     
   • Brake drum
     
   • Rear wheel
     
   • Negative battery cable
     

can u replace the bearing in the hub? will that fix your problem?