Serpentine belt schematic 2004 subaru H6 3.0 - 2004 Subaru Outback

Idler and Tensioner shown here

https://www.2carpros.com/diagrams/subaru/xt6/1989

See the videos in this link.

https://www.google.com/search?q=replace+serpentine+belt+on+1988+Subaru+xt6

..

2008 Jeep Liberty Belt Anon, Schematic belt.Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Install Replace Serpentine Belt Tensioner Idler Pulley 3 7L 2004 13...
2008 Jeep Liberty Serpentine Belt Removal
2008 Jeep Liberty Belt routing Google Search

Serpentine belt diagram 2002 ford taurus 3 0 2002 Ford Taurus
should be the same for 2003

Diagram reference number 1 in the image below:
"" Fitment: 2006 SUBARU B9 TRIBECA - 4 door

Application Notes:

Category: Electrical. Charging and Starting

SubCategory: Alternator / Generator and Related Components

Position: General

Part Number: 809221090


This is a Serpentine Belt that fits the 2006 SUBARU B9 TRIBECA - 4 door with the EZ30D engine. The Serpentine Belt is designed by SUBARU to be part of the Electrical. Charging and Starting-Alternator / Generator and Related Components. The Serpentine Belt has a position on the vehicle of General. The 2006 SUBARU B9 TRIBECA Serpentine Belt is a factory made SUBARU OEM part and it comes with a 12 month 12.000 mile warranty (parts only). Do not be fooled by an aftermarket SUBARU B9 TRIBECA Serpentine Belt! Buy a factory SUBARU part and receive peace of mind!
This factory part has a part number of 809221090. "

Click here to see your belt repair guide.

1. Removing the Serpentine Belt
   • 1 Park your Subaru on a level surface and open the hood.
     
   • 2 Disconnect the ground (black) battery cable using a wrench. This will prevent the cooling fan from activating.
     
   • 3 Locate the serpentine belt routing diagram in your engine compartment and compare it to the actual routing of the installed belt. Make sure the routing on the label matches the actual routing. If they do not match or there is no label, note the actual routing on a piece of paper for later reference.
     
   • 4 Locate the belt tensioner pulley on your Subaru model. If the tensioner is equipped with a squared hole, use a large breaker bar with a 1/2-inch (13 mm) drive. Otherwise, use a ratchet and socket of the proper size on the tensioner pulley center bolt.
     
   • 5 Rotate the tensioner pulley away from the belt to release the belt tension.
     
   • 6 Pull the belt off of one of the pulleys and slowly release the tensioner pulley back into position. Do not let the tensioner pulley snap back or you may damage an internal component.
     
   • 7 Finish removing the serpentine belt from the rest of the pulleys and the engine compartment.
     
   Installing the New Serpentine Belt
   • 1 Match the old belt to the new one and make sure they are of the same length and configuration. It is normal for the new belt to be slightly shorter since the old one has been stretched through use.
     
   • 2 Route the new serpentine belt through all of the pulleys except the tensioner pulley. Use the diagram on the engine compartment or your notes, as a reference, to properly route the belt.
     
   • 3 Insert the large breaker bar into the square hole or the ratchet and socket into the tensioner pulley center bolt.
     
   • 4 Rotate the tensioner pulley in the same direction you did to release the belt tension.
     
   • 5 Slide the serpentine belt onto the tensioner pulley.
     
   • 6 Release the tensioner pulley back into position.
     
   • 7 Look at all the pulleys and make sure the serpentine belt is properly seated on each one. Otherwise, release the belt tension and adjust the belt.
     
   • 8 Connect the ground (black) battery cable using the wrench.
     

OMPONENT

I need to know if you have a 2.0 or 2.3 and if you have A/C or not...

There is a distinct possibilty there is engine damage caused when the belt broke. It is best not to turn the engine at all once this happens. Sometimes you can be lucky and there be no damage. Let's hope that's so in your case. These belts are supposed to be replaced every 100,000km.

Download instructions from my website...

http://arraw.info/pdf/Timing Belt.pdf

<img src="http://www.mvreader.com/multiview/dayco/graphics/rtdiag/bkc.jpg" alt="2003 SUBARU OUTBACK - H6 3.0L 3000cc GAS FI N EZ30D" /><br>The website mvreader.com/multiview/dayco has listings for most cars' serpentine belts, as well as their installation instructions.

Hope this helps out,
matthew