Question about 2005 Hyundai Tucson

2 Answers

How do I remove the back bumper from a 2006 hyundai tuscon?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 869 Answers

Take help of the following steps to remove rear bumper on ur tucson.

Open the trunk of your vehicle.

  1. Unscrew all the screws on the inside plastic trim that covers your bumper to trunk connection.
  2. Pry the plastic piece out with a flathead screwdriver. You will expose the bolts that attach the rear bumper to the trunk.
  3. Unscrew the bolts connecting to the inside of your rear bumper. There should be four bolts.
  4. Unscrew the two to four screws connecting to your bumper from the inside of the rear wheel tire wells. These screws are on the area of the tire well that is closet to the bumper.
  5. Slide under the rear of your car. Use a flathead screwdriver to pop the plastic rivets out of place along the underside of the rear bumper. There should be four to six rivets.

  6. Squat behind your car and firmly pull the bumper off. There will popping plastic sounds, this is the pop-in-place plastic rivets that are the last pieces that hold your rear bumper in place.

Posted on Jan 28, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

Remove the tailgate package. Remove both rear lights. Remove the cover over the door lock receiver (two screws, pull straight up) Remove mud patches (three screws and a plastic plug / screw below) Then there is a screw on the left rear wheel houses. Dnne sits inside a hole in the rear edge. Remove all plastic plugs and screws you see above and below. Bumper is now free. Lytt til Les fonetisk Ordbok - Vis detaljert ordbokresultat

Posted on Jan 09, 2011

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1243 Answers

SOURCE: how to remove the back

you have to remove the intake plenum to access the rear plugs on the engine. it sounds rough but it is not that hard .just be sure to disconnect the sensors before pulling up on the plenum so not to damage them.

Posted on Jul 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have problem with my Hyundai Tuscon CRDI 2006, injector no 3 &4 are stuck cannot remove them- I have already taken out no 1 & 2 any ideas please on how to remove them


They are only held in by rubber grommets as you can see by the ones you removed.you will have to carefully pry them up with a screw driver or similar.

Oct 13, 2016 | 2006 Hyundai Tucson

1 Answer

Where is the transmission filter on a 2006 hyundai tuscon


that filter would be in the transmission you have to remove the transmission pan to get at the filter which will drain the fluid so be sure to have new fluid if you buy the service kit fir it then you will a new gasket as well

Feb 24, 2015 | Hyundai Cars & Trucks

1 Answer

Tuscon 07 starts when gas cap removed


Sounds like fuel tank vent is blocked,also check breather hole in fuel cap...

Jan 06, 2013 | 2006 Hyundai Tucson

1 Answer

I changed a timing belt on my 2006 hyundai tuscon and now the vehicle won't start


But it started and ran fine before this? If YES, then the answer's patently obvious eh? The belt was put on incorrectly, or more accurately, the timing has been set up wrongly. Sadly it seems you'll need to get someone to check the timing and get it reset properly. Best of luck!

Jun 10, 2012 | Hyundai Cars & Trucks

1 Answer

How do you replace the grill on a 2006 elantra sedan


The front bumper has to be removed to access the mounting screws holding the grill to the bumper (the mounting screws are on the back-side of the grill).

Sep 05, 2011 | 2006 Hyundai Elantra

1 Answer

How to remove the back plug on 2006 hyundai tuscon 2.7


you have to remove the intake plenum to access the rear plugs on the engine. it sounds rough but it is not that hard .just be sure to disconnect the sensors before pulling up on the plenum so not to damage them.

Jul 20, 2011 | 2006 Hyundai Tucson

1 Answer

How to replace the back spark plug on a 2006 hyundai tuscon


remove upper intake plenum to access back plugs.

Jul 13, 2011 | 2006 Hyundai Tucson

1 Answer

Rear Brakes


yes they can be just pushed in

Mar 30, 2009 | 2005 Hyundai Tucson

Not finding what you are looking for?
2005 Hyundai Tucson Logo

2,088 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...