1998 tiburon 5 speed manuaL transmission

Depends on your engine.

1980 JEEP CJ-7 2.5L 4-cyl Engine Code [B]
CAPACITIES
Engine, GM without filter..........2.4 quarts[1]
Wix Filter ........ 51040
Cooling System, Initial Fill..........8.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....25 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 4.2L 6-cyl Engine Code [C]
CAPACITIES
Engine, without filter..........5.0 quarts[1]
Wix Filter..... 51522
Cooling System, Initial Fill..........11.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....30 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 5.0L 8-cyl Engine Code [H]
CAPACITIES
Engine, without filter..........4.0 quarts[1]
Wix Filter..... 51258
Cooling System, Initial Fill..........13.0 quarts
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A904, 30RH..........7.0 quarts
3 speed A999, 32RH..........8.4 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

Oilman

Believe it or not the ford standard transmissions take atf used to be a heavy gear oil but now its ATF. You have a indicator stick that unscrews on the R-passenger side of the trans case and it should be 4-5 quarts, Good luck.

Muncie 4 (117MM) speed---Lubricant Type---------80W-90 Gear Oil
Muncie 5LM60 (HM-290) 4 & 5 Speed ---------Lubricant Type------Syncromesh Trans Fluid T2850

Oil Capacity= 5 Speed (85mm & 109mm)--3.6 pt (US)
(New Venture Gear 4500)--8pt (US)

4 Speed= (85mm)--3.6pt (US)
(117mm)--8.4pt (US)


Hope this helped you ??

usually gear oil goes in it, but sometimes i have seen atf automatic trans fluid too. but most likely gear oil like a 75w90

1992 Ford Ranger came with two different type of 5 speed stander transmission's that year.

For a Mazda stander trans it take's Automatic transmission fluid Mercon.

for a Mitsubishi stander transmission it take's Ford manual transmission fluid.

Hope this help's.

DONT USE GEAR OIL IN A MANUAL TRANSMISSION. it will blow your seals out. the gear oil is too heavy and will block passages in the tranny

75W/90 gear oil.

is the car auto or manual??
if auto you pour fluid down the tube you check your fluid at. make sure when you check the trans fluid the car is running or you will get the wrong reading.

if car is manual then you have to get a rachet and remove the plug on side of trans and pour the right gear oil into it (note not trans fluid GEAR OIL)

LUBRICANTS & FLUIDS
Engine Oil
Grade 1......API*
100% Synthetic 0W-20 Motor Oil
SAE 5W-20 XL Synthetic Motor Oil
SAE 0W-30 Synthetic Signature Series Oil
Above 9°F......15W-40
Above 0°F......10W-30
Above 19°F......20W-50
All Temps......5W-20
Manual Transmission,.....GL-4
75W-90
Synthetic Manual Transmission and Transaxle Gear Lube 75W-90
Automatic Transmission,4 Speed AT.....SLF[1]
Synthetic Automatic Transmission Fluid
Fluids
Power Steering Fluid.....PS
AMSOIL Universal Synthetic Power Steering Fluid
Brake Fluid.....HB
Series 500 High Performance DOT 3 Brake Fluid
Clutch Fluid.....HB
Series 500 High Performance DOT 3 Brake Fluid

1. Kia automatic transmission fluid, SP-III.


PLEASE DON'T FORGET TO RATE!!!!!

There are 3 transmissions that could be in your car,the 3 speed auto and 4 speed auto overdrive,and of course the manual 5 speed.The 3 speed is designated the 3T40,the 4 speed auto is the 4T40E trans.To check the fluid level,first,the car has to be warmed up to at least 100 degrees Fahrenheit.The car has to be raised in the air,as there is a steel plug in the trans case that has to be removed to check the fluid level.The plug takes an 11 mm or 7/16" socket or wrench and is located on the passenger side of the trans case,near where the passenger side axle engages into the trans.The procedure is to warm the car up to at least 100 degrees,engage the shifter into each gear selection pausing for about 5 seconds in each gear,then remove the plug.If fluid drips out,it is full.If no fluid drips out,add fluid through the top of the trans after removing the red plastic cap,and make sure to use a long funnel to avoid a mess.Add fluid until it drips out the hole.When done,replace the plug and cap.Just a note,a transmission does not "use" fluid like an engine uses oil.If you have to add fluid,that means there is a leak that needs to be repaired.Good luck