I have a holden barina i need the torque setting for the wheel bearing nuts

1995 C1500 spindle nut torque procedure? - CK5 Network

https://ck5.com > ... > General Discussion > The Garage
Jan 31, 2005 - while rotating the hub in a foward direction torque the nut to about 12ft lbs. Keep doing that a few times to ensure the bearings are seated.

96 gmc: torque..the front spindle nut..C1500 - JustAnswer

https://www.justanswer.com > Car Questions > GM Repair
Sept 16, 2011 - Torque nut (12) 10-12 ft lbs while turning the wheel assembly forward by hand. This will seat the bearing. Loosen nut (12) to a just loose ...
1 answer · Top answer: You can attach the magnetic base to the end of the spindle or to the brake caliper bracket. ...

• 
  

  1996 chevy: the torque setting for front wheel bearing..1500 4x4

  https://www.justanswer.com > chevy > 1tv6x-1996-che...
  Feb 18, 2009 - Outer Tie Rod Nut (C and K Models) · Shackle to Frame Nut and Bolt (C3500HD) · Shock Absorber Nuts (K Models) ; 62 N·m · 95 N·m · 90 N·m ; 46 lb ft.

Torque specification guide - PDF4PRO

https://pdf4pro.com > cdn > torque-specification-...
PDF
Front and rear axle nut torque specifications for FWD, RWD and 4 W/D vehicles. Torque specification guide. Form #457377. April, 2007.

BUY A REPAIR MANUAL FOR IT AND READ IT

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

Any chance u got a manual to refer to like get reference books from reliable-store.com .. I'm kinda sure that's all u need..

In the link

https://www.justanswer.com/australia-car/gyqys-cylinder-head-bolts-torque-holden-barina-tk.html

Cylinder Head Bolts - Camshaft Support Housing and Cylinder Head Mounting Bolts .............. 25 N.m+60°+60°+60°+15° (18 lb ft+60°+60°+60°+10°)

https://www.google.com/search?q=2007+holden+barina+cylinder+head+torque+specs

..

170 foot pounds

In this link Peter Case

https://www.google.com/search?q=Barina+c14se.+What+are+cylinder+head+bolt+torque+specs

..

about 7 ft lbs or tighten lightly then 1/4 turn

4-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake shoes
     
   • Rear halfshaft nut and loosen the halfshaft from the hub
     
   • Wheel hub and place it in a vise
     
   • Inner wheel bearing race from the hub
     
   • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
     
   • Parking brake cable from the steering knuckle
     
   • Brake line from the wheel cylinder and support the knuckle
     
   • Lower shock absorber nut
     
   • Lower ball joint by holding the ball joint stud
     
   • Upper ball joint
     
   • Coil spring while noting the location of the insulator
     
   • Steering knuckle cam
     
   • Steering knuckle
     
   • Snapring and press out the outer wheel bearing race from the knuckle
     

     Rear hub and bearing
     Click to Enlarge

To install:

1. Install or connect the following:
   
   • New wheel bearing into the steering knuckle
     
   • Snapring to the knuckle
     
   • Wheel hub
     
   • Steering knuckle cam and hand tighten the bolt
     
   • Coil spring
     
   • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
     
   • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
     
   • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
     
   • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
     
   • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
     
   • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
     
   • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
     
   • Brake shoes
     
   • Rear wheel
     
   • Negative battery cable
     
2. Fill and bleed the brake system.
   
3. Check and adjust the wheel alignment as needed.
   

2-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake drum
     
   • Wheel hub nut
     
   • Wheel hub
     
   • Inner wheel bearing race from the hub
     
   • Snapring
     
   • Wheel bearing outer race from the knuckle
     

     Rear hub and bearing
     Click to Enlarge

     Rear hub removal
     

     Inner wheel bearing removal-rear hub/bearing
     

     Rear wheel bearing removal-2wd
     

     Rear wheel bearing removal-4wd
     

To install:
Install or connect the following:

• Wheel bearing in to the knuckle
  
• Snapring
  
• Wheel hub into the wheel bearing
  
• Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  
• Brake drum
  
• Rear wheel
  
• Negative battery cable
  

  Rear wheel bearing installation
  
  hope this helps if so send testimonial comment or even any other questions you have
  

please understand there are a lot of items on a car that require torque settings every thing from the lug nuts to every engine bolt, and transbolt. please be more specific