Question about 2007 Hyundai Accent GS Hatchback

Open Question

How to clear 3cde message to re attempt again. i did it just now.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1684 is the code what does it mean when it say battery been unhooked in the last 50 starts.


The message is there to allow the inspectors that check for emissions compliance to know whether or not you (or someone else) has disconnected the battery in any attempt to erase or clear codes in the last 50 start-stop cycles. In jurisdictions that only use the on board computer to verify emissions compliance, they will often automatically fail the vehicle for emissions on this message and you must return after the message clear to prove the vehicle is fault-free.

Feb 15, 2016 | 2001 Chrysler PT Cruiser

1 Answer

Cant pass emissions,i need at least one of the not ready status to become ready status out of the oxygen senson, evaporative system, catalyst


drive it. I am betting you have recently "cleared" codes which also clears readiness monitors in an attempt to better control people cheating the system. After enough drive cycles are reached the monitors will pass if nothing is wrong and turn to ready. If the problem that the codes implicated where not fixed than the check engine light will again come back on and you will again fail your attempt to pass emissions.

Drive it for a week or so and see what happens.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Aug 15, 2015 | Cars & Trucks

2 Answers

Starting disabled


charge the battery. disconnect the cables and hook it back up. you should be able to turn on the ignition key to clear out message. if that doesnt work you can plug in an odb reader and clear out the codes.

Dec 16, 2017 | 2005 Chevrolet Uplander

1 Answer

What is an average cost to service the Stabilitrak System in a 2002 Cadillac Escalde


If the system fails to turn on or activate, the StabiliTrak light along with one of the following messages will be displayed on the Driver Information Center (DIC): TRACTION CONTROL OFF, SERVICE TRACTION CONTROL, STABILITRAK OFF, SERVICE STABILITRAK. If these DIC messages appear, make sure the StabiliTrak system has not been turned off using the StabiliTrak on/off button. Then turn the steering wheel clockwise from the nine o'clock position to the three o'clock position. If this clears the message(s), the vehicle does not need servicing. If this does not clear the message(s), then turn the vehicle off, wait 15 seconds, and then turn it back on again to reset the system. If any of these messages still appear on the DIC, the vehicle should be taken in for service.

Mar 17, 2013 | Cars & Trucks

1 Answer

"Tire Pressure Sensor Fault" keeps coming on on my message center, each time I start the car


You need to put a scanner on the computer and read the codes, then repair the codes called for and using the scanner clear the codes and you will be ok. The button on the message center doesn't reset the computer it just clears the code from the screen.

May 27, 2017 | 2003 Ford Expedition

1 Answer

I replaced the right rear taillight and the message center keeps giving me the auxiliary tail light message.. how can I get this message to go away?


try disconnecting the battery for around 10 minutes that should clear any stored messages if it comes up again get back to me.

Dec 25, 2010 | 2007 Mercedes-Benz ML320 CDI

1 Answer

I had to purchase a new battery for the car. After installation, the COdE message for the radio would not allow me to play the radio. I attempted to put in the 5 digit code but was unsuccessful. What do...


After two tries, the radio assumes tampering, and stops receiving the unlocking code. Disconnect the battery for 10 minutes or so, and attempt again to introduce the code.

Aug 25, 2010 | 1996 Honda Accord

1 Answer

My raido in my 97 acura rl is locked up on the ''code'' screen. how do i reset the radio so i can put the code in?


briefly disconnect earth lead on battery.this should clear screen then punch in code you only have three attempts before it blocks up again

Feb 28, 2010 | 1997 Acura RL

2 Answers

Car won't start


Your immobilizer is enabled. Try locking/unlocking the doors with the remote five (5) times, this should remedy.

May 31, 2009 | 2006 Volvo S40

1 Answer

How to reset the service due message on a 1999 e430


Disconnect your battery for 5-10 minutes, this will clear the message.
Keep in mind, however, that if your computer receives the same trouble code again, the light will turn back on.

-R

Sep 29, 2008 | Mercedes-Benz E-Class Cars & Trucks

Not finding what you are looking for?
2007 Hyundai Accent GS Hatchback Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...