At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The inertia switch, also known as the fuel cutoff switch, is typically located in the cargo area of the vehicle, behind the trim panel or carpeting. Here are the general steps to remove the inertia switch from a 2004 Ford Expedition:
Turn off the engine and remove the key from the ignition.
Locate the inertia switch in the cargo area of the vehicle.
Disconnect the negative battery cable to ensure the switch is not live.
Press the release button or tab on the switch to unlock it from its bracket.
Gently pull the switch out of its bracket and disconnect the electrical connector from the switch.
If you need to replace the switch, install the new switch by reversing the above steps.
It's important to note that some Ford models have a reset button on the inertia switch that can be pressed to reset the switch instead of completely removing it. If your Expedition has a reset button, it may be worth trying that before attempting to remove the switch.
I see you have a fuel shut off switch right side floor board side panel.
Two fuel pump fuses and one fuel pump relay in under hood fuse box
the link below is for the owners manual fuse, relay & shut off valve reset info starts Page 188 https://justgivemethedamnmanual.com/ford/2002-ford-expedition-owners-manual/
The fuel pump relay will be in the fuse box. Also, keep in mind that Ford has a fuel inertia switch located in the rear interior panels. If the car was in an accident or hit in the rear, the switch will need to be reset. Hope this helps you out.
Power comes from a fuseable link to the pump relay, then to the inertia switch on the dark green and yellow wire. Power from the inertia switch to the pump is on the pink blue or pink black wire.
Try resetting fuel pump. I do believe the reset button is on the forward passengers side of vehicle. The button is behind the plastic shield. Reset once or twice. This hopefully will fix your problem. Look in your manual for exact placement of fuel pump reset button
Here is the manual
FUEL PUMP SHUT-OFF SWITCH
After a collision, if the engine cranks but does not start, the fuel pump
shut-off switch may have been activated. The "Fuel Reset" indicator light
will illuminate in the instrument cluster. The shut-off switch is a device
intended to stop the electric fuel pump when your vehicle has been
involved in a substantial jolt.
1. Turn the ignition to the OFF position.
2. Check the fuel system for leaks.
3. If no fuel leak is apparent, reset the fuel pump shut-off switch by
pushing in the reset button.
4. Turn the ignition to the ON position. Pause for a few seconds and
return the key to the OFF position.
5. Make a further check for leaks in the fuel system.
The fuel pump shut-off switch is
located in the passenger's foot well,
behind the kick panel.
Could be a bad fuel pump if the fuel is not being delivered to the engine.
This happened to a 99 ford expedition we acquired where no fuel was being delivered, even though the reset button for the inertia switch was pushed or toggled.
The fuel pump shut-off switch is
located in the passenger’s foot well,
by the kick panel.
Use the following procedure to reset the fuel pump shut-off switch.
1. Turn the ignition to the OFF position.
2. Check the fuel system for leaks.
3. If no fuel leak is apparent, reset the fuel pump shut-off switch by
pushing in on the reset button.
4. Turn the ignition to the ON position. Pause for a few seconds and
return the key to the OFF position.
5. Make a further check for leaks in the fuel system.
×