Remove ignition lock to switch link 1995 suburban

Most likely the switch has died. They over heat and melt inside and at the plug. Also look at the ignition wires under the dash, Sometimes they can chaff against the column or frame.

just take steering wheel off and lock plate then turn signal switch then youll be at ignition take bolt out pull cylinder out put new one in

Locksmith.

Or a 20 min. video.
1995 Chevrolet Suburban Ignition Module Replace

To troubleshoot these issue, for ignition switch replacing procedure:---
Click the link below:---

IGNITION SWITCH REPLACING

It depends on vehicle to vehicle. But it's not very difficult on mot of cars to replace ignition switch. Basic theory of replacing ignition switch is same for all car models. -----

To replace ignition switch on your vehicle, I suggest you few helplinks with proper ignition switch replacing procedure. View its details and you can replace ignition switch on your vehicle.

-------------

Click the link below: ------

----------

How to remove ignition switch on VW Car models?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html

-------------

How to replace Ignition Lock Cylinder on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-lock-cylinder.html

--------------

Ford Taurus: Ignition Switch & Steering Column Replacing?

http://repairhelpcenter.blogspot.in/2012/06/ford-taurus-ignition-switch-steering.html

-----------

How to replace Ignition Switch on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-switch-on-acura.html

--------------

How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html

-----------

Ignition Switch Will Not Turn Off?

http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html

---------

These will help.

Thanks.

The switch just lifts off the rod from the lock cyinder after you unbolt it so not sure what it is you are doing here?

you need haynes repair manual for 1993 suburban it has photos and information you need to help you replace ignition switch.i am mechanic i use haynes,chiltons and gm manuals.if you are a home mechanic do it your self you need haynes repair manual it has step by step instructions to remove the steering wheel and remove lower steering column reason i say need haynes repair because your steering wheel has a air bag in it you need to see how to remove air bag in steering wheel you need to read through the entire ignition switch removal procedure if you are going to replace ignition switch with keylock cylinder you will also need steering wheel puller. you need a tool compress lock plate to remove lock plate retaining ring from steering shaft in order to get to the ignition switch in the steering column below turn signal switch.

Remove the lower steering column cover and check to see if the rod from the ign. lock and tumbler to the ignition switch is binding up. If it's ok, you're problem may be the bearing under the steering wheel being broken.

1 disconnect the negative cable at battery
2 place the ignition switch in the lock position. if the key lock cylinder has been removed, pull the actuating rod up until a definite stop can be felt then move down one detent
3 lower and support the steering column
4 remove the ignition switch retaining screws and lift the switch out of the steering column jacket
5 prior to installation, make sure the ignition switch is in the lock position
6 connect the accuating rod to the switch
7 press switch into position and install screws
8 install steering column bolts

Take The Driverside Control panel Off The Door,And Check Conection On The Main Switches,These Vehicles Have Locks On Them, And If They get loose The Stop Working,Also Check The Little Switch Towards The Front of Panel,It Also May Be Loose,Use Caution,The Clips Are Fragile..

U must dis-arm the airbag 1st, disconnect the battery for 30 minutes before you begin work, then remove the airbag, the retaining screws are at the back of the steering wheel down in holes I believe, after that remove the safety clip at the top of the steering wheel threads, then the steering wheel nut, you will need a steering wheel puller to remove the steering wheel, they are about $10 from any parts store, after the wheel is removed remove the airbag clock-spring rotating contact, then remove the turn signal switch, there will be 3 screws holding the turn signal switch in, remove them, then remove the lower trim under the dash and crawl under and and disconnect the large flat connector at the bottom of column, this will allow u to pull the turn signal switch up and out of the way, don't force anything be patient, under the turn signal switch on the right of the area above the ignition lock cylinder u will see a black headed screw, it may be a tamper proof torx/star screw head or a phillips, remove it, then turn the ignition to the on position and slide the ignition switch out, reverse it all and put it back together. take your time, don't rush, good luck, contact me with any further questions.