Hi i have a 2001 2.7 td nissan terrano does any body know the torque wrench settings for the cylinder head bolts cheers

Here you go, the year is close enough.

What are the Nissan almera 2004 1.6 16v cylinder head ...

Answers https://www.answers.com > What_are_the_Nissan_alm...
Feb 22, 2023 - THE NISSAN ALMERA 2005 1.6 16V CYLINDER HEAD TOURQUE SETTINGS. 1.Tighten 29N.M using the correct sequence. 2.Tighten 50°. 3.Tighten 55°.

..

Yes, I can help you with the cylinder head torque wrench setting for your Hyundai Atos 1.0cc. Here are the torque specifications:

First pass: Tighten all bolts to 18 lb-ft (25 Nm)
Second pass: Tighten all bolts to 45 lb-ft (61 Nm)
Third pass: Tighten all bolts to a final torque of 65 lb-ft (88 Nm)
It's important to tighten the bolts in the correct sequence. The sequence is as follows:

10 6 2 3 7
9 5 1 4 8

Note: The numbers above refer to the cylinder head bolts in the correct sequence. Always use a calibrated torque wrench to ensure that the bolts are tightened to the correct specification.

I hope this helps you with your cylinder head installation. If you have any further questions or concerns, feel free to ask.

Hi,



Here is torque steps for cylinder head bolts on your vehicle:



Install the cylinder head and torque the head bolts in numerical order using the following 5-step procedure:

Torque all bolts to 22 ft. lbs. (29 Nm).
Torque all bolts to 58 ft. lbs. (78 Nm).
Loosen all bolts completely.
Torque all bolts to 22 ft. lbs. (29 Nm).
Torque all bolts to 54-61 ft. lbs. (74-83 Nm), or if an angle wrench is used, turn all bolts 80-85 degrees clockwise
Torque sequence:

Hi valve clearance inlet 0.010 in (0.254 mm). Exhaust 0.017 in (0.432 mm) normal running temperature .. Cylinder head bolts Torque 65 - 70 lb/ft.,.. Cheers

Tighten the cylinder head bolts. Tighten the cylinder head bolts is sequence to 29 Nm (3.0 kgf-m, 22 ft. lbs.). Use a beam-type torque wrench. When using a preset type torque wrench, be sure to tighten slowly and do not overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt and retighten it. Make sure the threads are clean, new heads bolts are best.

Hi Eduardo:
Check this information (click over pics for zoom)...



Fig. 20: Exploded view of the cylinder head assembly-VG30E engine




Fig. 15: Cylinder head loosening sequence-VG30i and VG30E engines




Fig. 17: Cylinder head torque sequence-VG30i and VG30E engines


Install the cylinder head with a new gasket. Apply clean engine oil to the bolt threads and seats, then install the bolts with washers (beveled edges up) in the correct position. Note that bolts 4, 5, 12 and 13 measure 5.00 in. (127mm), and are longer than the others. The other bolts are 4.17 in. (106mm) long.

Tighten the bolts in the proper sequence, in the following stages:
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 43 ft. lbs. (59 Nm).
Loosen all bolts completely.
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 40-47 ft. lbs. (54-64 Nm). Or, if you have an angle torque wrench available, tighten them an additional 60-65 degrees.


Hope this helps; remember to rate this answer. Good luck.

if this is a aluminum head it will be a torque to yeild. you will need brand new head bolts and a torque to yeild wrench, torque to yeild is not a set value but the stretching point of the bolt, wich a torque to yeild wrench will tell you when the bolt is starting to stretch then you stop and torque is achieved. often the starting torque is approx 30pds then you go back through with the torque to yeild wrench. if it has a cast iron head it will have a set value determined by the manufacture which on this car i do not know off hand. I hope i at least led you in the right direction

I need the torque settings and pattern for a Kia Sportage 2.2

Hi! i hope this will help you.
tighten in 2 steps:
1st - 22ft.lbs
2nd - 58ft. lbs
then loosen all bolts completely.
Final torque is in 2 steps:
1st- 22ft. lbs.
2nd - 54-61ft. lbs
( if angle torquing in 2nd step, turn all bolts 80 to 85 degrees clockwise with an angle torque wrench. ) i hope this will help you.

1. Tighten the cylinder head bolts sequentially in three steps. NOTE: Perform each step twice. 1st step torque: 39 Nm (4.0 kgf-m, 29 ft. lbs.) 2nd step torque: 69 Nm (7.0 kgf-m, 51 ft. lbs.) 3rd step torque: 98.1 Nm (10.0 kgf-m, 72.3 ft. lbs.) Use a beam-type torque wrench. When using a preset-type torque wrench, be sure to tighten slowly and not to overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt, and retighten it from the first step.