Low beam headlights not coming on 2002 cev avalanche

ok when push the lever forward the high beams don't stay on ? then that lever should be replaced cause that's ur dimmer switch to switch between high/low beam lights if the lever is bad can surge you headlight and blow the headlights, have you check headlight bulbs its rare but it has happened that both blow at the same time

headlight relay or switch

It can be faulty low beam lamp or its connection issue for low beam lamps.

There are few solved helps links with proper solution to troubleshoot these issues.I suggest you to refer the links below.Click the link:----
Passenger side low beam out?

http://repairhelpcenter.blogspot.com/2012/01/passenger-side-low-beam-out.html

------------
Low beam HID light goes out? http://schematicsdiagram.blogspot.com/2012/01/low-beam-hid-light-goes-out.html
----------2007 Dodge Caliber: Low Beam Headlight Not working http://technoanswers.blogspot.in/2012/06/2007-dodge-caliber-low-beam-headlight.html
-------------Chevy Tahoe: Low Beam Lamps are not working? http://technoanswers.blogspot.in/2012/04/chevy-tahoe-low-beam-lamps-are-not.html
----------2001 Chevrolet Tahoe: Both Low Beam Lamps Not Working? http://technoanswers.blogspot.in/2012/04/2001-chevrolet-tahoe-both-low-beam.html
--------------2002 Toyota Tacoma: Low Beams not working? http://technoanswers.blogspot.in/2012/04/2002-toyota-tacoma-low-beams-not.html
-----------Low beam headlights Modification? http://schematicsdiagram.blogspot.in/2012/04/low-beam-headlights-modification.html
-----------DRL and Low beams not working? http://schematicsdiagram.blogspot.in/2012/04/drl-and-low-beams-not-working.html
-----------These will help.Thanks.

These trucks are known for bad multifuction switches.
the switch that i talk of is the signal switch , the handle is the switch, it bolts to side of steering column . this switch controls the signals and the headlights and high /low beams. the other thing is the headlight switch connector, the connector some times goes bad and starts to melt or just comes out of the connector. you will need to remove the cover to steering column, the screws are located under the bottom cover in holes. remove cover and check connector and then test for power if you have power going into switch but not coming out then switch is bad.

the last thing is to make sure the bulbs are good , make sure the headlight bulbs are good , and also the driving light bulbs, test for power at the connectors to those lights to.
You will need to do a little testing to find the problem.

Most likely Relay #46 in the underhood fuse panel is bad, try swapping it with #45 to isolate problem.

1. Open the hood.
2. Remove the park/turn signal lamp assembly.
3. Remove the headlamp retainer pins.
4. Pull out the headlamp assembly in order to access the electrical connector.
5. Disconnect the electrical connector.
6. Remove the bulb from the headlamp assembly by twisting the bulb counterclockwise.

INSTALLATION PROCEDURE

IMPORTANT:

• Replace a high beam bulb with another high beam bulb. The high beam bulb has a red gasket.
• Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a yellow gasket at the base.

1. Install the new bulb to the headlamp assembly by twisting the bulb clockwise in order to lock in place.
2. Connect the electrical connector to the bulb.
3. Install the headlamp assembly.
4. Install the headlamp retainer pins.
5. Rotate and lock the pins in place.
6. Install the park/turn signal lamp assembly.
7. Inspect the operation.

2 adjustments one on top and one under lens

How to Shift my headlight beam from position.
from I replace my headlight it's spatting directly on the ground..What can i do to change it from position

The most common cause of this problem is the multifunction switch.

Email me on [email protected] and I can scan some pages of my manual for you if you would like. I just this spring replaced my low beams and its not something you want to do in semi darkness and no i didnt take out battery or air filter of my 2002 Avy.