Question about 2008 Chevrolet Silverado 2500HD 2WD

1 Answer

I need step by step instructions for replacing headlight bulb on my 2008 chevy 2500hd.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 8,980 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2011 gmc sierra 1500 left headlight out. replaced bulb twice but still out. right side and both high beams work fine


Check for power at the socket. If you have power there bulb is not making good contact.

Nov 30, 2013 | 2008 GMC Sierra 2500HD 2WD

1 Answer

2009 GMC 1500 Serria, I need instruction on removing the headlight so I can replace the bulb. It doesn't want to pull out.


If you take the bolt off the windshield washer refill, you can lean it left or ride to allow you room to reach in and replace the bulb. Don't feel bad, after about an hour of ******* around I accidentally noticed this.

Feb 12, 2011 | 2008 GMC Sierra 2500HD 2WD

2 Answers

I have a 2008 aveo. i took off the headlight but i can not get the plastic casing off to change the bulb.


If you are talking about the headlight casing, where the clear headlight casing connects to your back headlight casing, that isn't the way to change the light bulb, you're going to damage the seals that protect water, and humidity.
Here's a good site to visit http://wiki.answers.com/Q/How_do_you_replace_headlight_bulbs_in_Chevy_Aveo

Feb 01, 2011 | 2008 Chevrolet Aveo5

2 Answers

How do i remove headlight to change bulb in 2007 chevy 2500HD


For the driver side just locate the bulb in question. Rotate the bulb housing 45-90 degrees counter clockwise. Pull bulb out and disconnect wiring harness. replace bulb then reverse steps. For the passenger you will have to remove the aircleaner box. to do this pull up on the box, it should pop up then proceed with original directions for driver side.

Dec 12, 2010 | 2007 Chevrolet Silverado 2500HD

1 Answer

Need to replace headlight bulb 2007 hhr


H13 HALOGEN HEADLIGHT BULB, SOLD INDIVIDUALLY -- Low 55/high 65-watt halogen bulb; 12.8 volts; P26.4t base; A high quality, direct fit OE replacement headlight bulb

3c8c3dc.jpg


How to Replace a Headlight Bulb
(DIY Complexity: Easy / Time: 0.9 hour)

Parts:
1. Headlight Bulb

Tools:
1. Screwdriver
2. 1/4 in. Drive Ratchet
3. Socket Set

Steps:
Step 1 Open the hood and locate the headlight assembly.
o Tip: Most headlight assemblies have a place in the rear to gain access to the headlight bulb.
o Tip: It is recommended that headlight bulbs are replaced in pairs.
o Tip: Always make sure the struts on the hood can fully support the weight of the hood so that it does not close on you while working. The use of a hood prop can securely hold it in place.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Gain access to headlight bulb.
o Tip: It is a good idea to check the high beam and low beam headlight bulbs at this time.

Step 3 Disconnect the wiring harness and replace the old headlight bulb with a new one.

Step 4 Turn on the headlights and check high and low beams to verify repairs.

Hope this help (remember rated this help). Good luck.

Mar 30, 2010 | 2008 Chevrolet Hhr

1 Answer

Change headlight on 2008 Chevy Malibu


Hi there,

Well first you can please follow the below steps -
1. Make sure the ignition key is in the off position and the headlight switch is off. Release the hood latch.
2. Open the hood and locate the top of the headlight assembly where you intend to change the headlight. If a plastic shroud is present, locate the center bolt and remove it with a ratchet and a socket. Lift the shroud out of the way to access the headlight assembly retaining brackets. Some later models may feature a snap-release shroud requiring no tools to remove.
3. Locate the brackets on the top rear of each side of the headlight assembly. Lift them all the way up to align the hole on the bottom of each bracket to the retaining tabs on the assembly.
4. Pull the assembly forward away from the Malibu, but be careful not to scratch the bumper. There are three guide pins that require unseating. The guide pins are what aim the headlights and it may take some wiggling to get the pins from their seats.
5. Support the assembly with one hand and then reach behind the unit with the other. The low beam bulb is on the outside, the high beam bulb is on the inside. You can also replace the parking light if desired. Locate the wire harness connection. Un-clip the wire harness from the back of the bulb socket. Remove the bulb by turning it counterclockwise 1/3 of a turn to align the release tabs of the ring and the assembly. Wiggle the bulb out of the assembly.
6. Place the latex gloves on your hands before opening the package of the replacement bulb. Oil in our skin can damage the glass bulbs of halogen headlights.
7. Carefully insert the new bulb into the ring and then align the tabs of the ring to the tabs of the headlight assembly. Push inward and then twist clockwise 1/3 of a turn to lock the bulb in place. Reattach the wire harness. Rest the headlight assembly inside its cavity and test the operation of the headlight before securing the headlight assembly in place. Be sure to turn the lights and ignition back off.
8. Align the three guide pins to their seats and push the assembly back into them gently until they snap into place. Replace the retaining brackets by pushing them downward to lock into place. Replace shroud, if applicable. Remove the tools and old bulb and close the hood. Post comments for further help or information......

Good Luck!!

Mar 27, 2010 | 2008 Chevrolet Malibu

1 Answer

Cobalt 2005 ls headlight bulb replacement


Instructions Things You'll Need:
  • 9007 LL halogen headlight bulb
  • Wrench
  • Gloves or clean rag
  1. Step 1 Set the parking brake and remove the keys from the ignition to ensure your Chevy Cobalt won't roll while you're replacing the headlight bulb.
  2. Step 2 Open the hood by pulling the hood release latch located under the instrument panel on the driver's side of the car. Locate the secondary release latch on the front of the hood at the center, slightly towards the driver's side. Slide the latch to the left to release the hood and raise it.
  3. Step 3 Locate the headlight assembly and remove the bolts by turning them counterclockwise. Set the bolts aside in a safe place, so you won't misplace them.
  4. Step 4 Remove the plastic fasteners from the headlight assembly molding. Carefully pull back the front fascia, or molding. You may need an extra pair of hands to perform this slightly awkward task.
  5. Step 5 Grab the headlight assembly and pull it towards the radiator at a slight angle to remove it. This should provide easier access to the headlight bulb and wiring harness.
  6. Step 6 Lift the plastic locking tab on the wiring harness to disconnect the bulb base. Then, disconnect the wiring harness from the bulb socket and remove the black retainer by turning it counterclockwise.
  7. Step 7 Disconnect the bulb socket by turning it counterclockwise. Remove the old bulb from the socket by firmly, but gently pulling it straight out.
  8. Step 8 Replace the old bulb with a new 9007 LL halogen headlight bulb. Put your headlight assembly back together by reversing the steps when you disassembled it. Use 89 inch-lb torque when retightening the headlight assembly

Feb 26, 2010 | 2006 Chevrolet Cobalt

1 Answer

How do you get access to the day time headlight bulbs to replace them on a 2004 Chevy 2500 HD crew cab.


Pull on the flat "clips" to unlock the headlights, remove the headlight assembly. You can then access the DRL bulb sockets, squeeze in the tab on the socket and twist a 1/4 turn to release the socket (clockwise as viewed from the front of the lens).

Oct 25, 2009 | 2004 Chevrolet Silverado 2500HD

1 Answer

How do you change headlight on Chevy 2008 Cobalt?


Open the hood by pulling the hood release latch located under the instrument panel on the driver's side of the car. Locate the secondary release latch on the front of the hood at the center, slightly towards the driver's side. Slide the latch to the left to release the hood and raise it Locate the headlight assembly and remove the bolts by turning them counterclockwise. Set the bolts aside in a safe place, so you won't misplace them.Remove the plastic fasteners from the headlight assembly molding. Carefully pull back the front fascia, or molding. You may need an extra pair of hands to perform this slightly awkward task.Grab the headlight assembly and pull it towards the radiator at a slight angle to remove it. This should provide easier access to the headlight bulb and wiring harness.Lift the plastic locking tab on the wiring harness to disconnect the bulb base. Then, disconnect the wiring harness from the bulb socket and remove the black retainer by turning it counterclockwise.Disconnect the bulb socket by turning it counterclockwise. Remove the old bulb from the socket by firmly, but gently pulling it straight out.Replace the old bulb with a new 9007 LL halogen headlight bulb. Put your headlight assembly back together by reversing the steps when you disassembled it. Use 89 inch-lb torque when retightening the headlight assembly bolts.

Sep 05, 2009 | 2008 Chevrolet Cobalt

1 Answer

Passenger Low Beam Headlight needs replacement!!!


You could remove the air filter cover and then you will be able to reach the bulb.

Apr 12, 2009 | 2004 Chevrolet TrailBlazer

Not finding what you are looking for?
Cars & Trucks Logo

868 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...