Cars & Trucks Logo
Posted on Nov 13, 2010

How do i change the oil pump on my 2000 chevy silverado

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

Problem Solver:

An expert who has answered 5 questions.

  • Contributor 1 Answer
  • Posted on Oct 03, 2011
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Problem Solver:

An expert who has answered 5 questions.

Joined: Apr 16, 2011
Answers
1
Questions
1
Helped
729
Points
1

How to change a/c oil in 2000 silverado?

5 Related Answers

Anonymous

  • 1450 Answers
  • Posted on Feb 10, 2010

SOURCE: How many quarts of oil does a 2000 chevy silverado

if it is a v8 it will take 6qts v6 will be 5 qts

Ad

Josh Murphy

  • 28 Answers
  • Posted on Dec 14, 2008

SOURCE: 2000 Chevy Silverado need to reset oil change code.

Turn the ignition key to the run position and pump the accelerator 3 times within 5 seconds.

Please leave feedback!

Anonymous

  • 1 Answer
  • Posted on Feb 19, 2009

SOURCE: FUEL PUMP FOR CHEVY SILVERADO

fuel filter? how about power to the fuel pump,loose ground wire to chasis? wiring harness? terminals clean at point of connection?did you check the fuel pump relay? Relay is located in electrical center under the hood on the driver side.relay and fuse legend will be on bottom side of cover, you sould be able to switch with another relay that you know works, ie: switch horn relay with fuel pump relay, honk horn to insure both relays are working when either relay is inserted into horn slot. Do you by chance have the electrical schematic drawing for the fuel pump?

Anonymous

  • 59 Answers
  • Posted on Jul 28, 2009

SOURCE: front axle differential on 2000 chevy silverado

Your pickup leaks just like everyone elses. what you need to do is go down to your local parts store and get an inline fuel filter (your local chevy dealer should also have these available just for this problem), preferably see thru then, where your vent runs up the inner fender cut the line about 4 inches down from the vent and install the filter. this will cure your problem

Anonymous

  • 105 Answers
  • Posted on Jul 29, 2009

SOURCE: process to change fuel pump on 2001 chevy silverado 1500

DROP THE FUEL TANK MAKE SURE YOU GO ABOUT HALF WAY THEN UNHOOK ALL THE LINES AND TERMINALS SO AS TO NOT DAMAGE THEM ALSO YOU NEED TO RELEASE THE FUEL PRESSURE AT FUEL RAIL BEFORE REMOVING ANY LINES

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How to change fuel pump on a 2000 chevy truck?

first step is to drop fuel tank pump is inside tank
0helpful
1answer

Chevy 2005 silverado low oil pressure replaced oil sending unit and the cluster no noise from engine

Put a gage in the sending unit hole and see if the oil pump is weak, that is the best way to tell if the engine pump is ok.
0helpful
1answer

How do you reset the oil change on a 2000 chevy silverado

TURN KEY ON PRESS GAS 5 TIMES IN 5 SECONDS, START ENGINE.
13helpful
1answer

How do I get rid of the change oil message on dashboard. I had a 2000 Chevy Silverado 5.3 liters and just changed the oil but still get the message. And, is it better to change the oil every 5,000 miles or...

Turn the key to the on position. Do not start. Pump the gas pedal all the way to the floor 3 times. This will reset the oil life.
Please rate by checking one of the four thumbs ups.
Thanks! Have a GREAT DAY!
4helpful
1answer
23helpful
1answer

How to reset the change oil light on a 2003 chevy silverado

Information courtesy of synthetic-direct.ca
Chevrolet Suburban/GMC Yukon XL, 2000-05 Chevrolet GMC Trucks Silverado, Sierra, 1999-05 Chevrolet Venture 2000
Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.
Best of luck.
Greg
0helpful
1answer

Changed oil pan gasket now i dont have much oil pressure

If oil pressure was fine before you changed the gasket, it's likely that some debris was loosened up (probably under the pan baffle) and got onto the oil pump pickup, restricting flow. The only other cause of low pressure would be worn engine bearings, which would not happen just by changing oil pan, unless you messed with either bearings or pump while pan was down. Remove the pan and carefully inspect the pump pickup for debris!!! DO NOT DRIVE VEHICLE 'TILL YOU HAVE CORRECTED THIS OR YOU WILL DAMAGE BEARINGS!!!
12helpful
1answer

2000 Chevy Silverado need to reset oil change code.

Turn the ignition key to the run position and pump the accelerator 3 times within 5 seconds.

Please leave feedback!
0helpful
1answer

Lose of oil pressure

yes you will not be able to clear the pickup
Not finding what you are looking for?

739 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...