At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Drain or siphon the washer solvent from the reservoir.
Detach the electrical connectors from the washer.
Disconnect the hose from the washer pump.
Loosen the nut at the bottom of the washer reservoir.
Unfasten the 2 nuts, then remove the washer solvent reservoir.
Remove the washer pump from the container.
If necessary, remove the solvent lever sensor switch from the washer solvent container.
Fig. 2: Exploded view of the washer fluid reservoir, pump and level sensor
To install:
Install the solvent level sensor switch in the washer solvent container. The tab on the solvent level sender switch must be lined up with the slot in the hole.
Install the washer pump into the reservoir, making sure the pump is pushed all the way into the container seal.
Install the washer solvent reservoir and secure with the 3 nuts. Tighten the nuts to 44 inch lbs. (5 Nm).
Attach the electrical connectors to the solvent level sensor and washer pump.
Connect the hose to the washer pump.
Fill the reservoir with washer solvent.
Connect the negative battery cable, then check for proper washer pump operation.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Find a quality Oldsmobile Silhouette Windshield Washer Reservoir and other used Mini Van parts ... For example: If you're looking for a Hood Latch, ... This part is also known as Oldsmobile Silhouette Wdsh Washer Reserv; ... 1999 MONTANA
? 2:34
https://www.youtube.com/watch?v=jCqbhK_-hjY
Jun 7, 2010 - Uploaded by 1A Auto Parts
How To Install Replace Windshield Washer Pump Many GM Vehicles ... can u tell Me were the Fuse located ...
The hose could be clogged ! Do you know where you add the washer fluid ? Somewhere on the bottom of that plastic bottle is the washer pump .
Removal and Installation
> WARNING: Windshield washer solution contains methanol, which is poisonous. Observe all cautions and warnings indicated on label of washer solution container. Failure to follow these instructions may result in personal injury.
> CAUTION: When replacing the windshield washer pump be careful not to damage the rubber grommet.
> CAUTION: Do not operate the windshield washer pump before filling the reservoir. Failure to do so could result in premature pump failure.
NOTE: When installing the reservoir, the filler neck must be lubricated using a water-based lubricant.
Remove the bolt and the windshield washer reservoir filler neck.
Remove the RH fender splash shield. For additional information, refer to Section 501-02 .
Remove the foam filler and remove the retainer.
Remove the 2 screws and the accessory drive splash shield.
To install, tighten to 5 Nm (44 lb-in).
Remove the nut, 2 bolts and position the A/C accumulator aside.
To install, tighten to 9 Nm (80 lb-in).
Unclip the A/C lines from the inner fender well.
Drill out the rivet and remove the bracket.
Remove the 2 bolts, slide the windshield washer reservoir assembly forward to release it, and position the washer reservoir aside.
Install the upper bolt followed by the lower bolt, and tighten to 5 Nm (44 lb-in).
Disconnect the windshield washer tube assembly from the pump and release the windshield washer tube assembly from the washer reservoir.
Disconnect the electrical connector from the windshield washer pump.
Release the wiring harness from the reservoir, and remove the washer reservoir.
the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.
Pump and Reservoir, Windshield Washer
Removal
Disconnect the battery ground cable (14301).
Raise and support the vehicle.
Remove the RH wheel (1007).
Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
Remove the windshield washer reservoir top bolt.
Disconnect the windshield washer reservoir fluid level sensor electrical connector.
Disconnect the rear window washer pump electrical connector from the rear window washer pump.
Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.
Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.
Loosen the two windshield washer reservoir side bolts.
Remove the windshield washer reservoir by sliding it out of the side slots.
Remove the windshield washer pump.
Installation
To install, reverse the removal procedure.
Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).
the only solution acording to the manual is to replace the reservoir... not much to say about that, u do have the option to patch it...be careful with the product u use to glue that patch. take care
right where the lines connect to reservoir, has little black seals that leak. I recommend removing reservoir, empty it out, then use RTV silicone and place it between seals and reservoir. Let it dry for FULL day. than reinstall.
NOTE: Windshield washer fluid should be collected in a container after the windshield washer hoses are disconnected. Disconnect the electrical connector and washer hoses.
×