How to program garage door opener - 1999 Volvo S70

SOURCE: programming the garage door opener

Homelink Garage Door Opener Programming Procedure:

The procedure described below was successfully applied to a 2005 Jaguar S-Type.

To begin with, several attempts were made using the programming instructions contained in my Jaguar’s owner’s manual. Though the procedure described in the owner’s manual was straight-forward and understandable, I was unsuccessful in getting the vehicle’s remote to make my garage door opener function. The particular garage door openers I have are both made by Genie. Both openers utilize the “Rolling Code” feature.

To begin with, be sure to clear previous codes on your Jaguar’s garage door opener by first turning (rotating) the ignition key to the “I” position (first notch). Next, simultaneously hold button 1 (left most button) and button 3 (right most button) down until the middle button’s red light changes from continuous on to a rapid flash. This process takes approximately 20-25 seconds. What follows is a two part process. In the first part, get your Genie portable remote and hold it near (approximately 3 inches away from) your Jaguar’s garage door opener console buttons. Choose which button on your Jaguar’s remote you wish to dedicate to your Genie door opener and simultaneously press and hold your Genie opener button and your Jaguar’s opener button. The red light on your Jaguar’s center button (button #2) will light up and within 1-2 seconds will begin to flash rapidly. You have just completed part 1 of the two part process.

Part two: Now it is time to utilize the “Learn” function on your Genie garage door opener. Press the “Learn” button on your Genie garage door opener. The red LED adjacent to the “Learn” button will begin to flash. You now have 30 seconds in which to program your Jaguar’s opener button. Using the same button you just used in the “part 1” procedure, press and hold the same button for several seconds. As before, your Jaguar’s red light in the middle button will light up and within 1-2 seconds, it will flash rapidly. Release the button you are programming. Now, here is the key piece of information! Once again, press and hold that same button. Once again, the center button’s red light will flash rapidly. Release your newly programmed button. This procedure proved successful in my application. Here is what has just happened. The first time you pressed your Jaguar’s remote button tells the Genie opener that it exists and that it is a viable candidate for making your life easier (opening the damn door). The second time you press your Jaguar’s remote button confirms to the Genie’s rolling code that your Jaguar’s signal is legitimate and is to be trusted from then on.

SOURCE: jag xj6 1996 97 programming the garage door openers

1. For first time training, press and hold the two outer HomeLink buttons, releasing only when the HomeLink indicator light begins to flash after 20 seconds. (Do not perform this step when training the additional HomeLink buttons.) 2. Position the hand-held transmitter 1-3 inches away from the HomeLink surface (located on your visor), keeping the HomeLink indicator light in view.
3. Using both hands, simultaneously press and hold both the desired HomeLink button and hand held transmitter button. DO NOT release until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. (The rapid flashing indicates successful training.)
Note: Some garage door openers may require you to replace step 3 with the “cycling” procedure noted in the “View Canadian Instructions” section.
4. Press and hold the trained HomeLink button and observe the indicator light.

• If the indicator light is solid/continuous, training is complete and your device should activate when the HomeLink button is pressed and released.
• If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light, proceed with the following training instructions for a rolling code device. A second person may make the following steps quicker and easier. Please use a ladder or other device. Do not stand on your vehicle to perform the next steps.

SOURCE: program instruction garage door opener in 2005 chrysler pacifica

You can download the operators manual for free at chrysler.com. It has the instructions to program the garage door opener. It's fairly easy with the instructions.

Good Luck,
Ray

SOURCE: programming garage door opener

there are three buttons on the opener.hold the 2 outside ones down for 25 to 30 seconds to erase the program. once the light (if equipped)flash rate changes,let go.
then push any one of the the three buttons and hold it in. and then push your remote. when the flash rate changes,the code is now in the homelink transmitter.the slt and slt plus had that feature.

SOURCE: program garage door opener in 2005 rx 330

There are 3 programmable Homelink buttons you can use for different remotes. Just to the right of the buttons there is an indicator light.

Decide which button you want to program. Point the none battery end of your remote 1"-3" away from the Homelink panel and press both the remote and desired Homelink button down and hold them down at the same time. After about 20 seconds, the Homelink indicator light will change from a slow flashing to a rapid flashing. You can then release both buttons,
If the garage door responds to the Homelink, your done! If not, your garage door uses a rolling codes transmitter and must be trained.
Find the training button on your garage door opener's transmitter (usually mounted on the ceiling). Press the training button and within 30 seconds press and release the programmed Homelink button twice. If the garage door opener operates, you're done! If not, press and release the Homelink button a third time and the garage door should respond. If it still does not, you may have a very old garage door opener with a none digital transmitter (like I did). In that case, you either need to buy a new opener or try to replace the transmitter with a modern digital unit (as I did). Advantage: cheaper than a whole new garage door opener.
Disadvantage: The newer openers incorporate safety features that my old opener does not have.