Brake Pads
Removal & Installation
Front
3.4L front disc brake assembly
4.0L and 4.7L front disc brake assembly
To Remove:
this section.
and the 4 anti-squeal shims
To Install:
CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.
NOTE: When replacing worn pads, the anti-squeal shims must be replaced
together with the pads.
Rear
To Remove:
this section.
To Install:
---
Removal & Installation
Note: Install the pad wear indicator facing downward.
pins.
Front
To Remove:
this section.
To Install:
Max Brakes includes all elements https://themotorsmasters.com/max-brakes-review/.
SOURCE: front brake pads
Just did this tonight... 7/21/08
You need a torx head T-55 Star Socket to remove the caliper bolt(s) and a large 3/4 in preferably with a 1/2 dr and large breaker bar or torque wrench with a 1/2 in dr. to remove the knuckle bolts. I should've taken pictures, but I did not. After studying this exact issue for an hour or so, I finally got everything to click. Steps as I proceeded. Loosen the top caliper nut using the T-55 torx bit, this will take some doing, if possible, use a breaker bar or something comparable, I used a standard 3/8 in. socket wrench and about a foot long hollow metal tube on the end as the breaker and after some muscle work (ouch!!) got it loose. Now there are 2 bolts that hold the caliper in place that need to come out. I used a 3/4 in socket on a 1/2 breaker bar to get these to break. I don't have the exact torque specs to put these back on, but I went about 40lbs on the knuckle bolts and closer to 80lbs on the caliper torx head screw. Once you have the caliper torx head bolt loose and the other 2 nuts off, you can rotate the caliper. Using a C-Clamp, compress the caliper so that it is completely compressed. Now, remove the torx head bolt and the pad assembly will swing out, at this point, you can remove the old pads and clips if you are replacing them as well. Reverse the order for installation using Lock-tite and the caliper grease you get from the parts store. I hope I don't have to mention removing the tires, using jack stands and being completely safe under there. Good Luck. The first side took me about 3 hours considering time and studying, the second side took about half an hour after already knowing what to do.. It gets easier each time you do it.
So far, I have replaced 2 fuel pumps (at home) first one took about 7 hours, second time around, only took about 2 hours. Front and Rear brake jobs. numerous small items, now I'm looking at a blinker switch (problem with left turn signal... rapid click, no light).. Also, the dash panel either needs repaired or replaced as the fuel gage is constantly up and down. If you or someone else has a suggestion here, I would appreciate it.
Thanks and remember... Practice Safe "Do it yourself"..!
SOURCE: Replace brake pads and rotor on Lincoln LS 2000 front wheels.
new rotors and new brake pads ...
...full job would include loaded calipers with all new hardware ..if you pay attention to disassembly you will not need a service manual necessarly..all is logical and straightforward...but you are dealing with safety so be sure you are good before taking a drive ...good luck
SOURCE: unable to remove front brake rotor
Hello, one "trick" is to grab a big hammer and hit the face of the rotor (the part that goes on the hub between the lug studs, NOT the brake pads ride on) several times. A lot of the vehicles I have done this with you really have to whack between the lugs pretty hard and a lot of times. Just make sure you don't hit the lug studs.
SOURCE: 2006 dodge ram 2500 4x4 diesel replace brake pads front and back
Straight forward job. Remove wheels, remove 2 caliper bolts per wheel, check bolts,and bushings for wear/corrosion and lubricate, remove calipers, remove brake pads, push caliper pistons into calipers, replace anti-rattle clips, put new pads in, put caliper and bolts in, put wheels on. Start truck and press brake pedal several times to take up slack and you're done.
SOURCE: what tool do i need to replace front brake pads on 2008 mariner?
You Will Need A 13-14 mm Wrench for Caliper Bolts .A Large Flathead Screwdriver to Spred open Caliper/Shoes to Remove Caliper from Rotor,
After rhis you Can use a LARGE "C" Clamp to CLOSE Caliper Piston.
2,119 views
Usually answered in minutes!
×