I need to remove inner door panel on 2004 colorada need to repair croocked glass

no need to remove the glass
simple wind it all of the way down
that gives you enough space to unhook the panel from the top of the door lift out the bottom and lift the panel across the opening will unhook from the top

Ford Fiesta Plastic Interior Door Panel Removal Guide ...

www.paulstravelpictures.com/Ford-Fiesta-Interior-Door-Panel-Removal-...

Ford Fiesta Interior Door Panel Removal Guide How to take off the plastic interior door panels in a 6th generation 2009-2015 Ford Fiesta to upgrade the ...

Ford Fiesta inner door panel removal (I removed the top one ...

www.fiestafaction.com/.../44959-Ford-Fiesta-inner-door-panel-removal-...

Jan 19, 2015 - 10 posts - ‎3 authors
This is an excerpt from the manual: Remove the rear door window glass. ... Route theinterior door handle cable and door lock actuator electrical connector through the ...Last edited by WildmaninME; 01-19-2015 at 07:41 PM.

Ford - door panel removal - fiesta - YouTube

? 2:19
https://www.youtube.com/watch?v=1URT13Yusjg
Oct 19, 2013 - Uploaded by one2three
this is the removal of a door panel from a ford fiesta 2001. ...Replacing Broken Inside Door Handle on 2007 Ford Fusion - Duration: 5:32. ... Ford Fiesta 1.25 2004 - Cleaning and adjustingrear brake drums - Duration: 8:47.

How To: 2012+ Ford Focus Rear Door panel removal(SE,ST ...

REMOVAL

1. Remove the watershield. (Refer to 23 - BODY/DOOR - FRONT/WATERSHIELD - REMOVAL)

2. Remove door glass retaining clips and secure the window in the up position using masking tape or equivalent(FRONT DOOR GLASS CLIPS).

3. Disconnect wire connector from power window motor, if equipped.

4. Loosen screws attaching front and rear window guide rails to inner door panel (FRONT DOOR MANUAL WINDOW REGULATOR - TYPICAL).

5. Remove screw heads on guide rails from key hole slots in inner door panel.

6. Loosen screws attaching regulator to inner door panel.

7. Remove regulator from inner door panel.

8. Extract rear guide rail through inner door panel rear access hole (FRONT DOOR POWER WINDOW - TYPICAL).

9. Extract front guide rail through front access hole.

INSTALLATION

1. Insert front guide rail through front access hole.

2. Insert rear guide rail through rear access hole.

3. Place window regulator in position on inner door panel.

4. Place screw heads on guide rails in position through key hole slots in inner door panel.

5. Tighten screws to attach front and rear guide rails to inner door panel.

6. Connect wire connector into power window motor, if equipped.

7. Install door glass.

8. Verify door glass alignment and operation.

9. Install sound shield and door trim panel

DIAGRAMS CAN BE FOUND ON JUSTANSWER,COM

Remove inner panel carefully. find 2 black circle stickers and raise glass to access 2 screws holding glass. Door vent does not need to be removed.

Front Door

1. Remove the door trim panel.
   
2. Remove the water dam.
   
3. Remove the inner and outer door belt weatherstrips.
   
4. Lower the window to the full down position and align the glass regulator arm with the access holes in the inner door panel.
   
5. Remove the front glass run channel.
   
6. Remove the nuts attaching the glass channel to regulator arm.
   
7. Separate the glass and lift it up and out.
   
8. Disengage the power window motor wire connector from the door harness, if equipped.
   
9. Loosen the bolts in slotted holes attaching regulator to door inner panel.
   
10. Remove the bolts attaching window regulator to inner door panel.
    
11. Remove the regulator through the access hole in the inner door panel.
    
12. Installation is the reverse of removal. Tighten the nuts attaching the glass to the lift plate to 7 ft. lbs. (9 Nm).
    

Power window regulator mounting—Dakota, Durango


Window regulator removal—Dakota, Durango

Posting more on next post for door panel removal and installation.

Saturn Coupes/Sedans/Wagons 1991-1998 Repair Guide
Door Glass and Regulator - REMOVAL & INSTALLATION
(see Figures 1, 2, 3 and 4)

1. Remove the outer door panel assembly. Refer to the sub-procedure under Door Locks, earlier in this section.
2. For rear doors, loosen the bottom fastener of the rear door stationary window assembly, in order to provide clearance, then apply tape to the lower half of the outboard exposed portion of the stationary window channel. The tape must be applied in order to prevent damage to the paint surface.
3. Lower the door glass, then use SA9148B, or an equivalent tool, to remove the glass nuts. Push the glass upward and rotate slightly, then remove the glass from the vehicle.
4. If the regulator is also to be removed, proceed as follows:
   1. Remove the inner door trim panel. Refer to the procedure earlier in this section.
   2. If applicable, unplug the wiring harness from the power regulator.
   3. Except for the rear door, remove the regulator cam bolts.
   4. Drill out the regulator rivets and remove the regulator from the vehicle.

To install:

1. If removed, install the regulator to the door assembly:
   1. Position the regulator to the door and secure using rivets.
   2. Except for the rear door, install the cam bolts.
   3. If applicable, connect the wiring harness to the regulator.
   4. Install the inner door trim panel to the vehicle.
2. Install the door glass into the door and over the regulator studs.
3. Install the glass nuts using tool SA9148B, or equivalent.
4. Check the door glass for proper operation and alignment.
5. If necessary, adjust the glass alignment. For rear doors, fore/aft adjustments are made after loosening the B bolts, while in/out adjustments are made when the A bolts are loosened.
6. Except for the rear doors, glass which is not running parallel to the door header may be adjusted after loosening the inner panel cam attachment bolts and adjusting the cam. If the glass is floating in the opening, lower the glass 3 / 4 downward, loosen the front guide fasteners, push the glass rearward to seat it in the rear channel, then bring the front glass guide back to the front edge of the glass. Apply a light finger pressure on the guide and tighten the fasteners.
7. Once the glass has been properly adjusted and is operating smoothly, install the outer door panel assembly.

Fig. 1: Remove the glass nuts using a suitable tool-front door shown



Fig. 2: Exploded view of the regulator mounting-except rear door



Fig. 3: Exploded view of the rear door regulator mounting



Fig. 4: Adjustments of rear door glass are made after loosening the A or B bolts


I hope help with this (remember rated this help) Good luck.

after u remove the bolts that hold it to the window regulator tip the window towards the front of the door and the top rear corner of the window should pop out and then u just lift hte window out,hope this helps

Window Regulator, Rear Door, Explorer Removal

1. Remove the rear door trim panel and watershield. Refer to Section 01-05B .

Trim Panel, Rear Door, Explorer, Hi-Series Four-Door Removal and Installation

1. Remove the two screws retaining the rear door trim panel (27406) located above the door handle.

1. Remove trim cup at the door handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.

1. To remove window regulator switch plate (14524) , use notch located at lower end of plate using a screwdriver to lift and remove.

1. Remove window regulator switch plate from rear door trim panel pulling wire harness from rear door trim panel .

1. From bottom of window regulator switch plate , remove two screws and disconnect connector from window regulator control switch (14529) .

1. At each plastic clip location, pry the rear door trim panel away from the door inner panel using the door trim panel removing tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent.

1. Remove panel, lift slightly to remove flange at the top of rear door trim panel from trough in the glass weatherstrip. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the rear door trim panel to the door inner panel, firmly loading clips into slots provided on rear door trim panel .
   
   

1. If equipped with power windows, disconnect the wire from the regulator.

1. Remove the rear door window glass as described in this section.

1. Remove the window guide, if equipped, (nuts and washers). Remove guide from door belt opening.

1. Remove three 1/4-inch rivets attaching motor bracket (electric) to inner panel and two 1/4-inch rivets attaching regulator lower bracket to inner panel. Use drift punch to knock out center pins for each rivet. NOTE: Use care not to enlarge sheet metal holes in the door inner panel when drilling.
   

1. Using a 1/4-inch diameter drill, drill out the remainder of the rivet.

1. Remove two upper regulator attaching nuts.

1. Remove regulator from the front door (20125) .

Installation

1. Lubricate regulator mechanism with Multi-Purpose Grease D0AZ-19584-AA or equivalent.

1. Install regulator into access hole in inner panel.

1. Position regulator using upper regulator studs and tabs on motor mounting bracket (electric) or cup mounting plate (manual).

1. Install rivets attaching regulator to door inner panel (1/4-20 x 1/2-inch bolt and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates).

1. Install two upper regulator attachment nuts.

1. Install door glass as outlined under Door Glass Installation.

1. Adjust glass as outlined under Adjustments .

1. Reconnect wire to regulator, if equipped.

1. Check operation of window regulator.

1. Install door watershield and trim panel. Refer to Section 01-05B .

how to remove drivers inner door panel on 2003 cadillac deville dhs to repair window trac