Suspension fault , normal height only pops up after driving about 2 minutes. need possable causes and estimate of cost to repair at dealership.

Air Suspension ??????

Air Suspension Description and Operation
Air Suspension
The primary mission of the Air Suspension System is the following for the rear suspension under loaded and unloaded conditions:
• Keep the vehicle visually level
• Provide optimal headlight aiming
• Maintain optimal ride height
The Air Suspension System consists of the following items:
• Air suspension compressor assembly
• Air suspension sensors
• Rear air springs
Important: The Air Suspension System must have a voltage supply of at least 12.6V to operate properly.
The Air Suspension System will maintain the rear D height within 4 mm (0.15 in) in all loading conditions and the leveling function will deactivate if the vehicle is overloaded. The side to side D height variation is maintained within 8 mm (0.31 in). After ignition is turned off, the air suspension control module (ASCM) will remain active for between 30 minutes and 2 1/2 hours. The system will exhaust pressure within 30 minutes after the ignition is turned off to lower the vehicle after unloading. In a temperature-controlled environment, the leakage of the complete load leveling system will not result in more than 1.4 mm (0.05 in) drop of rear suspension height at GVWR during a 24 hour period. If the outdoor temperature drops from +20°C (+68°F) to -5°C (+23°F), the rear D height may drop as much as 25 mm (1 in). However, the Air Suspension System should return to the specified D height when the ignition is again cycled to ON.

What is the problem ?

Diagnostic Trouble Code (DTC) Displaying
The Air Suspension system has an internal clock to prevent overheating if the compressor assembly is running for a prolonged period of time. If the system overheats, all leveling function stops until the system cools down. During this time, the indicator LED on the air inflator switch will be quickly flashing at a constant rate.
The other three diagnostic trouble codes are displayed with a blink code on the inflator switch LED. The Air Suspension Compressor Assembly shall begin to indicate the code when the condition to cause the code becomes current.
The number of the fault code shall be represented by the number of flashing pulses on the inflator switch LED. The flashing pulses shall have a repetition rate of 0.5 seconds and each code shall be separated by a 3.0 second delay. All codes shall be flashed in the order of occurrence of the fault. The blink code shall take priority over other processes that have access to the inflator switch LED. Refer to the following:
• DTC 001
• DTC 002
• DTC 003

Trim Height Uneven or Low ??????

Problems with the air suspension seem to be less frequent with the Sport than in previous Range Rover models, but they still do occur. One owner reports "Whenever my RRS is lowered to "access" level a suspension system fault message apprears.". Another reports " Had the RRS back less than 2 hours and another "suspension fault." Also kept receiving messages that the vehicle is raising slowly and vehicle will raise when system cools. Couldn't even drive because it wouldn't raise out of access mode. Anyway, back to the dealer. Picked the RRS up again today-dealer said the EAS compressor was faulty and replaced it. So far everything is ok." Overall, most of the problems seem to be related to bad suspension height sensors or bad compressors. Angus Wade of the Czech Republic had his suspension light come on when in Germany; it started yellow and then red, then disappeared when he stopped and restarted the engine -- and has not happened since. His dealer said they have seen this a bit.

Weak Compressor: An official Technical Service Bulletin (TSB) LS-204-004 addresses "ELECTRONIC AIR SUSPENSION (EAS) WARNING MESSAGE AND LAMP ILLUMINATION". This deals with the warning message "Suspension Fault - Normal Height Only" message appearing with the Air Suspension Warning Lamp on. Computer diagnosis shows pressure increasing too slowly or unable to pressurize, with no air leaks. The usual problem is the compressor exhaust valve sticking, causing an internal air leak when the compressor is active. The bulletin recommends renewing the air compressor (RQG500090 is the latest specification air compressor with a stronger exhaust valve return spring)and installing and updating the air suspension control module software using WDS disc 13 or later.

Suspension Fault Message (random): One owner reported getting random suspension fault messages on his brand new RR Sport purchased in June 2006, well after the fix was in for the weak compressor. His suspension Fault message and Suspension Warning Light (Amber) came on after 5 days of ownership. He stopped and restarted the car, which caused the light and message to disappear, but they came on again after 5 minutes. Later the same day, the warnings disappeared again.

I have heard that on 2006 models, EAS fault messages can be caused by an internal leak in the Air Suspension compressor exhaust valve. The fix is said to be replacing the compressor updating the software.

Hope helps.

Problems with the air suspension seem to be less frequent with the Sport than in previous Range Rover models, but they still do occur. One owner reports "Whenever my RRS is lowered to "access" level a suspension system fault message apprears.". Another reports " Had the RRS back less than 2 hours and another "suspension fault." Also kept receiving messages that the vehicle is raising slowly and vehicle will raise when system cools. Couldn't even drive because it wouldn't raise out of access mode. Anyway, back to the dealer. Picked the RRS up again today-dealer said the EAS compressor was faulty and replaced it. So far everything is ok." Overall, most of the problems seem to be related to bad suspension height sensors or bad compressors. Angus Wade of the Czech Republic had his suspension light come on when in Germany; it started yellow and then red, then disappeared when he stopped and restarted the engine -- and has not happened since. His dealer said they have seen this a bit.

Weak Compressor: An official Technical Service Bulletin (TSB) LS-204-004 addresses "ELECTRONIC AIR SUSPENSION (EAS) WARNING MESSAGE AND LAMP ILLUMINATION". This deals with the warning message "Suspension Fault - Normal Height Only" message appearing with the Air Suspension Warning Lamp on. Computer diagnosis shows pressure increasing too slowly or unable to pressurize, with no air leaks. The usual problem is the compressor exhaust valve sticking, causing an internal air leak when the compressor is active. The bulletin recommends renewing the air compressor (RQG500090 is the latest specification air compressor with a stronger exhaust valve return spring)and installing and updating the air suspension control module software using WDS disc 13 or later.

Suspension Fault Message (random): One owner reported getting random suspension fault messages on his brand new RR Sport purchased in June 2006, well after the fix was in for the weak compressor. His suspension Fault message and Suspension Warning Light (Amber) came on after 5 days of ownership. He stopped and restarted the car, which caused the light and message to disappear, but they came on again after 5 minutes. Later the same day, the warnings disappeared again.

I have heard that on 2006 models, EAS fault messages can be caused by an internal leak in the Air Suspension compressor exhaust valve. The fix is said to be replacing the compressor updating the software.

Hope helps.

The compressor should only run until the rear suspension reaches the desired height. If it continues to run after the suspension has raised to ride height then you may have a leaking air bag/solenoid or line. If you dont have any leaks it is possible the EVO(air suspension module} or relay is at fault.

Need to get the vehicle scanned for fault codes.
The most common issue is the air pump/compressor for the electronic air suspension.
Relatively easy to replace, but you still need to get the vehicle scanned for fault codes. Once the fault has been repaired, again you will need to get the faults cleared.
No really a DIY repair im afraid.

it could be from many reasons...sometimes even the ABS system will cause this fault or even the Steering position Sensor. if it comes and goes then inspect your height sensors as the early version of the height sensors are getting weak and like melting so it gives wrong reading which cause the fault...offer more info. and you'll get your solution

If the compressor has to run more than normal, there is likely a fault / leak in the system somewhere which these are notorious for. Check your airbags for leaks / spray all parts with a mist of water and soap to find where your air is escaping from.

I had a 1999 Expedition. When you put the 4x4 on it raises the vehicle an extra inch or 2.
It may help to turn the 4x4 off. Two wheel drive is a lower air setting.
Your original pump may still be good. The problem can be in the front. The compressor is not filling the front suspension to the cutoff point. It will lift the rear after the front end is at running height. Since you lost the front end first, the remaining air bled out there and then the rear came down. Once you shut down the car the suspension was done, all the air was let go.
There are adjustment solenoids on the body but you need someone qualified to repair this.

do you have just rear air suspension? here's rear only. 4 wheel different. Deler an run a diagnostic test with WDS machine and get fault codes.
-------------------------------------------------------------------------------------
The air suspension system is designed to improve ride, handling and general vehicle performance for static, on-road and off-road driving conditions:

• Ride is improved by using an air type spring (the soft ride is inherent).
• Handling is improved by maintaining constant vehicle attitude.

The system consists of unique rear air springs, the air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for the RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines and the use of air springs with air spring solenoids.
The air suspension system holds vehicle height when the rear hatch or any door is opened. The system stores rear vehicle height the moment any open door is detected. The system then maintains this height regardless of the addition or removal of a load. The system will return to its commanded height when all doors are closed or the vehicle speed exceeds 16 km/h (10 mph).
----------------------------------------------------------------------------------------
Air Suspension Height Sensor
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3.2 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm (3.2 in) of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket).
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level
------------------------------------------------------------------------------

• Uneven vehicle height

• Circuitry.
• Rear pneumatic fault.
• Air compressor assembly.
• Air suspension control module.

• Go To Pinpoint Test I .