SOURCE: NECESITO AYUDA..PROBLEMA EN ISUZU RODEO 2000.
ami carro sele tiro un sello dela transmision y se tiro todo el aceite lo pare de manejar selo pusieron y ahora enlas suvidas pierde velosidad y prende la luz abs
SOURCE: Arranca pero cuando calienta no
revisa el filtro de gasolina primero. a quitar filtro, sople en el, si sale gas por el otro lado facil filtro es bueno. si no sale cuando sople con su boca en filtro. cambie filtro, la bomba de gas puede estar mal tambien.
SOURCE: tengo una dodge caravan motor
The Dodge P1494 engine light code means Leak
Detection Pump Switch or Mechanical Fault.
A proper diagnosis must
be done, you can't simply replace the LDP and expect that to fix the problem.
It shouldn't hurt anything to keep driving it for a while until you can get
it fixed.
There is a technical service bulletin that applies to your vehicle and it mentions
that code specifically. I'm including it here for your information:
TSB-18-01-00
SUBJECT: Misdiagnosed Leak Detection Pump Systems With DTC P1494, P0442, P0455, OR
P0456.
MODELS:
1997 - 2000 (LH) Concorde/Intrepid/LHS/300M/Vision and others!
DISCUSSION: During evaporative system diagnosis, Leak Detection Pumps have mistakenly
been replaced. A thorough inspection for pinched, kinked, or disconnected
supply vacuum lines (as currently listed in the Powertrain Diagnostic Procedures)
is a critical step in diagnosing DTC P1494 (LDP SW OR MECHANICAL FAULT). Additionally,
the other evaporative leak faults (DTC P0442 - SMALL LEAK, P0455 - LARGE LEAK,
and P0456 - VERY SMALL LEAK) should have the supply vacuum lines examined
for pinches or kinks prior to any LDP component replacement. The supply vacuum
lines should be checked from the engine compartment all the way to the fuel
tank, including the LDP and purge system.
NOTE: VERIFY ALL RELATED SUPPLY VACUUM LINE ROUTINGS FOR PINCHES, KINKS,
OR DISCONNECTION'S BEFORE REPLACING LDP SYSTEM COMPONENTS.
If you need tha trasnaltion, couild check THIS LINK. Hope this helps.
Traduccion automatica:
El Dodge motor P1494 c?digo de luces de detecci?n de fugas de la bomba o el interruptor de falla mec?nica. Un diagn?stico correcto se debe hacer, no se puede simplemente sustituir el PLD y esperamos que para solucionar el problema. No debe doler nada que mantener la conducci?n por un tiempo hasta que te lo arreglen.
Hay un bolet?n de servicio t?cnico que se aplica a su veh?culo y se menciona que el c?digo en particular. Lo incluyo aqu? para su informaci?n:
TSB-18-01-00
ASUNTO:
Diagnosticado de fugas Sistemas de detecci?n de la bomba con DTC P1494, P0442, P0455, P0456 O.
MODELOS:
1997 - 2000 (LH) Concorde/Intrepid/LHS/300M/Vision y otros!
DISCUSI?N:
Durante el diagn?stico del sistema de evaporaci?n, de detecci?n de fugas bombas han sido sustituidas por error. Una inspecci?n minuciosa de las l?neas de vac?o pellizcar, torcer o desconectado de suministro (en la actualidad figuran en los Procedimientos de Tren Motriz de diagn?stico) es un paso cr?tico en el diagn?stico de DTC P1494 (PDL SW O AVER?A MEC?NICA). Adem?s, los otros fallos por evaporaci?n de fugas (DTC P0442 - peque?a fuga, P0455 - fuga grande, y P0456 - MUY PEQUE?OS DE FUGAS) deben tener las l?neas de alimentaci?n de vac?o examinados por pellizcos o vueltas antes de cualquier reemplazo de componentes del PLD. Las l?neas de alimentaci?n de vac?o se debe revisar el compartimiento del motor hasta llegar al tanque de combustible, incluyendo el PLD y el sistema de purga.
NOTA: VERIFICAR todo lo relacionado SUMINISTRO DE RUTAS l?nea de vac?o PIZCAS, torceduras, o desconexi?n ANTES DE CAMBIAR LOS COMPONENTES DEL SISTEMA PLD.
939 views
Usually answered in minutes!
ploblemas claxon
×