Code: U0140-LOST COMMUNICATION WITH BODY CONTROL MODULE What does this mean?

Yes that can happen

With all those codes, you need a good auto-electrician with a $5,000 pro grade scan tool computer. Most of this is Body Control Module issues.

U0141 Lost Communication With Body Control Module "A"

https://www.obd-codes.com > u0141
Code U0141 pertains to the BCM "A" or the wiring to the BCM from the engine control module (ECM). The code, depending on the year, make and model of the ...

U1403 - Implausible Fuel Level Signal Received - Engine ...https://www.engine-codes.com > u1403'What is U1403 code meaning? ... The Fuel Level Sensor signal is a direct input to the Body Control Module (BCM). The BCM transmits the fuel level message to the ...

U110C CHRYSLER Code - Lost Fuel Level Messagehttps://www.engine-codes.com > u110c_chrysler'What is U110C CHRYSLER code meaning? ... The Fuel Level Sensor signal is a direct input to the Body Control Module (BCM). The BCM transmits the fuel level ...

U110E CHRYSLER Code - Lost Ambient Temperature Messagehttps://www.engine-codes.com > u110e_chrysler'What is U110E CHRYSLER code meaning? ... The Ambient Temperature Sensor signal is a direct input to the Body Control Module (BCM). The BCM transmits the ambient ...

Code U0100 stands for Lost Communication with ECM/PCM. The powertrain control module (PCM) is the computer responsible for engine management. Like the other computers (known as modules) onboard your vehicle, the PCM communicates over a bus.U0100 - OBD II Trouble Code: Lost Communication with ECM ...

I checked the first 3 and they are all Can-Bus Communication issues. Press CTRL+F and type in the code and press enter.

https://www.dtcdecode.com/Jeep

This is the last one

Jeep DTC U0212 Make: Jeep Code: U0212 Definition: Lost Communication With SCM Description: With the ignition on. Battery voltage between 10 and 16 volts. Ignition Off Draw (IOD) fuse installed. Front Control Module (FCM) is configured correctly. Bus messages not received from the Steering Control Module for approximately two to five seconds Cause:

• CAN BUS CIRCUITS OPEN OR SHORTED
• DTCS RELATED TO BATTERY VOLTAGE, IGNITION, OR VIN MESSAGES
• STEERING CONTROL MODULE POWER AND GROUND
• FCM NOT CONFIGURED CORRECTLY
• STEERING CONTROL MODULE
• MODULE THAT SET THIS DTC

..

U0140 Lost Communication With Body Control Module

Read more at: https://www.obd-codes.com/u0140
Copyright OBD-Codes.com

A further search may explain the significance of "00/N".

BTW, the VE forum at "Just Commodores" website has a wealth of information for the do it yourselfer. Join up & use the search box.

HDM module ??????? No such module .
DTC U0100 00: Lost Communication With Engine/Powertrain Control Module (ECM/PCM)
DTC U0101 00: Lost Communication With Transmission Control Module (TCM)
DTC U0121 00: Lost Communication With Electronic Brake Control Module (EBCM)
DTC U0140 00: Lost Communication With Body Control Module (BCM)
DTC U0151 00: Lost Communication With Restraints Control Module
DTC U0155 00: Lost Communication With Instrument Panel Cluster (IPC) Control Module
DTC U0164 00: Lost Communication With HVAC Control Module
DTC U0168 00: Lost Communication With Vehicle Theft Deterrent (VTD) Control Module
DTC U0170 00: Lost Communication With Passenger Presence System (PPS)
DTC U0184 00: Lost Communication With Radio
DTC U0186 00: Lost Communication With Audio Amplifier
DTC U0194 00: Lost Communication With Digital Radio Receiver (DRR)
DTC U0198 00: Lost Communication With Communication Interface Module (OnStar®)
DTC U0209 00: Lost Communication With Heated Seat Module (HSM)
DTC U0214 00: Lost Communication With Remote Function Actuation (RFA)

These are all the modules onyour vehicle - no hdm module .

U0140 Chevrolet Lost Communication With Body Control Module P1629 Chevrolet Theft Deterrent Start Enable Signal Not Received http://www.carobdcode.com/u0422-gmc-invalid-data-received-from-body-control-module#.Vva4p8vmqQw

U0184 00
Lost Communication with Radio , did you replace factory radio ?
The communication among control modules is performed through the High speed GMLAN serial data circuits and the Low speed GMLAN serial data circuit. The modules that need real time communication are attached to the High Speed GMLAN network. The body control module (BCM) is the gateway between the high and low speed networks. Refer to Body Control System Description and Operation for more information about the gateway.
Signal supervision is the process of determining whether an expected signal is being received or not. Some messages are sent on a periodic basis and are interpreted as a heartbeat of a device. If such a signal is lost, the signal supervision part of the software will set a no communication DTC (U code) against the missing device. This code is mapped on the scan tool screen as a code against the physical device. A lost communication DTC typically is set in modules other than the module with a communication failure.
Does the vehicle start an run ?

are you okay nothing hapened to you right did you
bleed did you heart some where of your body

The message you are getting are not V's but U's, they sometimes are hard to read what the letter is but here is your answers:

U0155 Lost Communication With Instrument Panel Cluster (IPC) Control Module

U1100 Invalid or Missing Data for Primary Id
U110C No Fuel Level Bus Message

U0140 Lost Communication With Body Control Module