How do i program the key fob on my 2003 grand am se

Keyless Remote Key Programming Procedure:

1. Insert first programmed key into ignition and turn ignition switch to ON for 5 seconds. ...
2. Turn ignition switch to OFF and remove key.
3. Insert second programmed key into ignition and turn ignition switch to ON. ...
4. Turn ignition switch to OFF and remove key.

More items...

Key Fob Keyless Entry Remote for 2008 Jeep Grand ...

..

There are several methods of doing this - but your 2003 requires that you either go to the dealer for them to add a FOB with special equipment (ask if they'll do it for free - can't hurt). If you have time to kill, you can do it yourself with Method 3 as described and found at:

Key Fob Reprogramming General Cadillac Forums

Method 3 - Key Fob Auto Learn


This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming with Method 3. If the RCDLR recognizes a known good key fob during Method 3 programming, the programming mode will resort to Method 1.


The vehicle must be OFF.
Place the replacement key fob in the console pocket with the buttons facing forward.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time.
When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
Repeat steps 5-7 two more times, for a total of 30 minutes.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode.
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.

Good luck!

GRAND PRIX KEY FOB PROGRAMMING INSTRUCTIONS Transmitter Programming No Tools Required In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver.Up to 4 transmitters may be programmed Important Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver

a dealer can check with the vin number

Hey Lisa,
You are going to have to take the car and the key fobs to the dealership .
They will need all of the fobs , as they are all going to need to be reprogramed at once ;
The fob on an 07 Pontiac only can be programed using a diagnostic scan tool .
They will connect the scan tool to the vehicle.
Turn key to on position.
Select 1 body,
then select special functions
then select program key fob,
select the number of key fobs you want programed.
Press and hold the lock and unlock key simultaneously for about 15 seconds until the power locks cycle to confirm the remote is programed.

Hey Lisa,
You are going to have to take the car and the key fobs to the dealership .
They will need all of the fobs , as they are all going to need to be reprogramed at once ;
The fob on an 07 Pontiac only can be programed using a diagnostic scan tool .
They will connect the scan tool to the vehicle.
Turn key to on position.
Select 1 body,
then select special functions
then select program key fob,
select the number of key fobs you want programed.
Press and hold the lock and unlock key simultaneously for about 15 seconds until the power locks cycle to confirm the remote is programed.

you will need to take it to a dealer or some place that has a scanner to program key fobs
IMORTANT TAKE ALL THE KEY FOBS WITH YOU
once the vehicle is put in the learn mode all the fobs have to be programed

Your key can only be programed at the dealer. They have to use a scan tool and a unique id code that they get from the factory. It is done this way to help insure that the vehicle is less likely to be stolden.

if you have an original working fob and your owner's manual,it will explain procedure,otherwise will have to go to dealer to be programmed

you will need the dealership diagnostic tool to program the remote