Having same issue with my 2000 grand cherokee. sometimes fuel pump will prime and car starts the other 50% of time no fuel pump noise only smaller radiator fan will come on and make vibrating whining noise. I have changed out fuel pump and filter as well as checked and ruled out all fuses/relays involved. Need help too
If it is getting fuel and spark then make sure your ground cable is getting a good ground to the motor and the frame to the battery.
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/tom_db3a51ff0ca57f20
Need to check for spark at plug wire,also check for fuel pressure at fuel rail with key on,should have pressure.
it is getting fuel to fuel rail .but what does it mean if no spark at plug wire?
what engine do you have. It may have a bad crank sensor which is mounted on the bell housing.Have seen alot of the jeeps with this problem.
it is a v6 not sure of engine size but i wanna say 4.0
×
SOURCE: diagram to remove and install a fuel pump on 1999 jeep grand cherokee laredo
I apologize for not being able to provide a diagram, and it's been a while since I've replaced a fuel pump in a Jeep like yours, however the fuel pump for that vehicle is located within the fuel tank. You will typically disconnect power from the battery,relieve the pressure from the fuel rail to the injectors. In most cases the test port on the fuel rail has a schrader valve "valve core" like a tire valve, which utilizing a rag to absorb excess fuel you can depress to relieve pressure. You will then have to detach the fuel filler tube and vent tube at the filler neck. With a floor jack supporting the tank ,there should be a couple of bolts holding either two straps around the tank or a large cover that covers and supports the tank itself ,that will need removal. Once you have removed these and you should be able to access the top of the tank. Bear in mind you don't put the fuel pump/sending unit wiring harness or the fuel and vent tubing under too much strain as you lower the tank. you should have enough room to disconnect this wiring and fuel tubing. the tubing will probably have a quick disconnect setup where it attaches to the pump assembly. Once you have the tank on the ground take a suitable (non sparking drift and hammer) to tap the retaining ring that holds the pump in the tank, around the openig to release it. The pump assembly will be spring loaded and the top may pop up out of the tank. Just be sure to protect yourself from any fuel that might spray up. To reinstall can be a slight chore sometimes, as the assembly is spring loaded. It usually goes in with just a slight amount of effort though. Remember to replace the fuel sock on the pump and o-ring seal around the top of the opening. You can purchase just the electric pump, but I'd recommend replacing the whole fuel pump assembly. It will cost more in parts, but longer part warranty and lesser chance of further damaging the assembly are the benefits. Naturally installation is the reverse of removal. I'd recommend a new fuel filter as well, or shortly thereafter. Chrysler factory replacement units recommend draining all the old fuel from the tank and replacing with new fuel (never done that, and with the price of gas, probably won't start) I have never seen an adverse effect from not doing so. I hope this posting has helped.
SOURCE: fuse box diagram for 1995 jeep grand cherokee laredo
I have the same model Grand Cherokee Limited 5.2L V8, nice truck; for fuse panel description and locations, check page 7 and next. All the infor that you need is here: Jeep-ZJ-Grand Cherokee-Secc-8W-Wiring-Diagrams.
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.
Thank you for using FixYa, have a nice day.
SOURCE: 96 jeep grand cherokee 4.0
I ve put coil pickup' crank sensor' coil still no power to fuse block on finder' no fire to plugs ' don't here fuel pump, this is on one another one blows fuse to the firing ever time I turn the switch on
732 views
Usually answered in minutes!
I will be changing out crank sensor tomorrow and will let u know hows those solutions helped but have run into another problem now i have a no key light that comes on when u try to start it
i need a diagram of how to install the crank sensor..i do not have a manuel and cant afford a book from auto zone
i installed a new crank sensor and now my jeep is running fine
×