Have 2005 chevrolet 2500 hd and i have changed throttle sensors and gas pedal and even put new computer in it but the reduced engine power sign and light comes on it will run good for a week to a month then it will come on i have invested in everything when i have it scanned p 2135 code reads which is gas pedle but i already changed it so what could cause it now please help

engine losing power sign ??? .You mean ENGINE POWER REDUCED ? This has to do with electronic throttle control -Throttle Actuator Control (TAC) System Description

The throttle actuator control (TAC) system is used to improve emissions, fuel economy, and driveability. The TAC system eliminates the mechanical link between the accelerator pedal and the throttle plate. The TAC system eliminates the need for a cruise control module and idle air control motor. The following is a list of TAC system components:
• The accelerator pedal assembly includes the following components:
- The accelerator pedal
- The accelerator pedal position (APP) sensor 1
- The APP sensor 2
• The throttle body assembly includes the following components:
- The throttle position (TP) sensor 1
- The TP sensor 2
- The throttle actuator motor
- The throttle plate
• The engine control module (ECM)

TAC System Default Actions/Reduce Power Modes
There are 2 reduce power modes that the engine control module (ECM) can default to if an error is detected in the throttle actuator control (TAC) system. If an accelerator pedal position (APP) sensor 1 or APP sensor 2 circuit fault, throttle position (TP) sensor 2 circuit fault, or if a TP sensor 1 circuit fault is detected with some APP angle, the ECM goes into one of the 2 reduce power modes. In this mode, the engine torque is limited so that the vehicle cannot reach speeds of more than 100 km/h (60 mph). The ECM remains in this reduce power mode during the entire ignition cycle even if the fault is corrected.
If there is a condition with the throttle actuator control circuits, throttle actuator command vs actual position fault, return spring check fault, or a TP sensor 1 circuit fault, the ECM goes into the other reduce engine power mode. In this mode, the engine speed is limited to 2,500 RPM and the 3-6 fuel injectors are randomly turned OFF. At this time the Reduced Power indicator is commanded ON. The ECM remains in the reduce power mode during the entire ignition cycle even if the fault is corrected. Observe, if a TP sensor 1 or throttle actuator control circuit fault is present at the time the vehicle is at idle, with no accelerator pedal angle, the engine may stall.
© 2022 General Motors Corporation. All rights reserved.

You need to have a qualified repair shop check it out.

Throttle Actuator Control (TAC) System Description
You have APP- accelerator pedal position sensors or one of the Throttle position sensors is going bad ! In the (TAC) system ! This is drive by wire or electronic throttle control . If you take it to the dealer or a ASE certified repair shop they can check the DTC'S - diagnostic trouble codes ! This is nothing for a DIYer to mess with ! This system can set 7 different DTC'S

Reduced Engine Power Mode When the PCM detects a condition with the TAC system, the PCM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
?€¢
Acceleration limiting--The control module will continue to use the accelerator pedal for throttle control; however, the vehicle acceleration is limited.

?€¢
Limited throttle mode--The control module will continue to use the accelerator pedal for throttle control; however, the maximum throttle opening is limited.

?€¢
Throttle default mode--The control module will turn off the throttle actuator motor and the throttle will return to the spring loaded default position.

?€¢
Forced idle mode--The control module will perform the following actions:

-
Limit engine speed to idle by positioning throttle position, or by controlling fuel and spark if throttle is turned off.

-
Ignore accelerator pedal input.

?€¢
Engine shutdown mode--The control module will disable fuel and de-energize the throttle actuator.


Drive by Wire Function and Diagnostics by Wells

Hi Steve , your vehicle has electronic throttle control . I don't know if you are aware of this. The gas pedal have position sensors an a wiring connector with 4-6 wires .these wires are connected to the engine computer . an there is a electric motor on the throttle body assembly , the computer opens an closes the throttle . You probably have codes stored in the engine computer .
Reduced Engine Power Mode When the PCM detects a condition with the TAC system the PCM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
?€¢
Acceleration limiting--The control module will continue to use the accelerator pedal for throttle control; however, the vehicle acceleration is limited.

?€¢
Limited throttle mode--The control module will continue to use the accelerator pedal for throttle control; however, the maximum throttle opening is limited.

?€¢
Throttle default mode--The control module will turn off the throttle actuator motor and the throttle will return to the spring loaded default position.

?€¢
Forced idle mode--The control module will perform the following actions:

-
Limit engine speed to idle by positioning throttle position, or by controlling fuel and spark if throttle is turned off.

-
Ignore accelerator pedal input.

?€¢
Engine shutdown mode--The control module will disable fuel and de-energize the throttle actuator.

Drive by Wire Function and diagnostics by Wells

If this is "fly by wire" throttle, any misalignment between gas pedal and TPS will cause this issue. Failure of the gas pedal sender is so common Lokar company makes a replacement pedal unit that is much better than stock.

The automotive trouble code P2138 throttle/pedal position sensor/switch D/E voltage correlation refers to a problem related to the throttle's ability to open and close properly. Replace (suggest) the sensor (black object) on the throttle body.

It's all tied together in the computer system . When you start to loose control the computer takes over reducing engine power , applying brakes etc... to bring vehicle back into control . The throttle body on your vehicle is computer controlled . electronic throttle control . the gas pedal has sensors , the throttle body has sensors an a electric motor . The lights came on because the computer disabled these systems .

cam or crank sensor failing

It is the APP sensors , Your vehicle has electronic throttle control . P2122 Throttle Pedal Position Sensor Switch Circuit Low Your best bet would be to take it to a qualified repair shop .

The reduced engine power happens because there is a problem with the electronic throttle control . Some people call it drive by wire ! The gas pedal has sensors inside , position sensors , connected electrical to the PCM - engine computer , the throttle body on the engine has a DC electric motor an also has position sensors . These are also connected to the PCM electrical . The PCM reads the position sensors which indicate how much your pressing on the gas pedal . then hopefully it opens the throttle the same amout .

The throttle actuator control (TAC) system delivers improved throttle response and greater reliability and eliminates the need for mechanical cable. The TAC system performs the following functions:
• Accelerator pedal position sensing
• Throttle positioning to meet driver and engine demands
• Throttle position sensing
• Internal diagnostics
• Cruise control functions
• Manage TAC electrical power consumption
The TAC system includes the following components:
• The accelerator pedal position (APP) sensors
• The throttle body assembly
• The engine control module (ECM)

Reduced Engine Power Mode
When the ECM detects a condition with the TAC system, the ECM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
• Acceleration limiting--The ECM will continue to use the accelerator pedal for throttle control, however, the vehicle acceleration is limited.
• Limited throttle mode--The ECM will continue to use the accelerator pedal for throttle control, however, the maximum throttle opening is limited.
• Throttle default mode--The ECM will turn OFF the throttle actuator motor and the throttle will return to the spring loaded default position.
• Forced idle mode--The ECM will perform the following actions:
- Limit engine speed to idle by positioning the throttle position, or by controlling the fuel and spark if the throttle is turned OFF
- Ignore the accelerator pedal input
• Engine shutdown mode--The ECM will disable fuel and de-energize the throttle actuator.

GM Electronic Throttle Body Circuit Descriptions And Testing Tips

Tons of videos on youtube for these systems , there can be a variety problems , from wiring , worn out sensors , the DC motor , computer etc....