Question about 1981 Chevrolet Corvette
Start with dirty fuse connection and then look for mouse wire damage
Posted on Dec 30, 2017
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
http://www.20thstreetauto.com/specials/spec58.htm here are smoked ones. http://cincinnati.craigslist.org/pts/966430154.html mirrored glass http://cgi.ebay.com/ebaymotors/CORVETTE-78-82-MIRRORED-T-TOPS--TOP--CORVETTE-ROOF_W0QQitemZ330300599122QQcmdZViewItemQQimsxZ20090114?IMSfp=TL090114126005r1464 pairs i will see if i can find 1
Posted on Jan 15, 2009
I'll tell you, but when you go to do it, you'll probably curse Chevrolet, your car, and me! lol!
You have to reach behind the dash. Even with the seat in the back position, you'll turn into a contortionist! Place an old couch cushion, or something similar on the ground/driveway next to the car, with the door open. Kneel on the couch cushion. Reach up under the dash, and back behind it, with your left hand, while holding onto the steering column with your right.
It's hard to describe this to someone who has never done this before. (Just think. You'll be the expert, when someone you know asks you, when you're done!)
You are feeling for a plastic bulb holder. This holder is about the size of a dime. It resembles one of a gas stove's knobs. It has a round base, and from the middle of the base, it comes up into rectangular shape. If you look at this -> T <- the base is the top of the T. Turn the T upside down, and you'll have the basic shape.
This plastic holder has the lamp bulb in it. You turn it to the RIGHT.
As you face the instrument cluster, it is turned to the Right. You just turn it one quarter turn, then it will come out.
Once you get one in your hand, you'll know why it was difficult to describe. You'll also immediately see how it turns in, and locks into place.
The bulb itself it extracted, by holding the bulb holder in your hand, bulb facing you. You push in, and turn the bulb to the Left.
It is at this point, that I advise you to wear some protective gloves of some kind. The bulb base, could be corroded down in the socket. You may exert enough force to break the bulb, and cut your fingers.
I advise Safety above ALL ELSE!
I also advise that you replace one bulb at a time.
Notice the brass metal ring around the bulb holder base?
This corrodes after time, giving a poor contact. You can take a little fine steel wool, and clean it up. Use care as the steel wool can catch, and bend the brass ring, misshaping it.
Behind the dash panel that you can't see, is a thin plastic flat strip.
Another thing hard to describe. Envision a large U shaped flat piece of plastic, on the back of your instrument housing. The U shape will be upside down, in relation to how it sits on the back of the instrument housing. It's about 1/32nd of an inch thick, and about 2 inches wide.
There are thin flat strips of copper, making a path all the way around this strip. There are holes in this strip, for the various lamp bulbs. The flat copper strips go around these holes, making a connection to the bulb holder. That's what that brass ring on the bulb holder contacts, when it's screwed in.
Posted on Apr 18, 2009
SOURCE: 1981 corvette seat conversion
you will need to pull off the four retaining nuts holding seat in place. Measure the length and width of bottom support frames. Many seats are interchangable.
Posted on May 11, 2009
I would ahve the alternator tested to see if it was bad first, if so I would replace it and see if that improves your choke situation. If the alternator is not putting out enough voltage it can affect other systems in you car including an electric choke system.
Posted on Apr 08, 2010
Testimonial: "Great advice and very quick response. "
Hello: The voltage regulator is inside the alternator (generator) The generator can be overhauled. The brushes, diodes, rectifier bridge and voltage regulator all can be replaced along with the stator, rotor and bearings although now days it may be cheaper to replace the alternator.
Posted on Jul 22, 2011
Tips for a great answer:
Jan 31, 2014 | 1981 Chevrolet Corvette
Apr 18, 2013 | 1981 Chevrolet Corvette
Apr 12, 2013 | Chevrolet Corvette Cars & Trucks
Aug 18, 2010 | 1981 Chevrolet Corvette
Apr 08, 2010 | 1981 Chevrolet Corvette
Jul 02, 2009 | 1981 Chevrolet Corvette
Apr 18, 2009 | 1981 Chevrolet Corvette
Aug 04, 2008 | 1981 Chevrolet Corvette
Jun 23, 2008 | 1981 Chevrolet Corvette
133 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: