2000 windstar transmission code 715 turbine speed sensor need to replace, where is it and should I do it.

question edited for clarity and spelling.
Question moved to model category.

2pc -autotransmission Speed Sensor For Toyota Daihatsu ...

AliExpress https://www.aliexpress.com > ...
high quality: Made of high quality material, durable and practical to use. acceleration sensor: Perfect to replace your old or broken car oem throttle speed ...
Rating: 5 · ‎ 1 review · ‎ US$29.08 · ‎ In stock

Daihatsu Terios 2000-2006 Automatic Transmission (2).pdf

Scribd https://www.scribd.com > document > Daihatsu-Terios-2...
Apr 28, 2004 - AUTOMATIC TRANSMISSION INTRODUCTION INSTRUCTION ON AUTOMATIC TRANSMISSION VEHICLES BASIC CHECKS AND ADJUSTMENT TESTING HYDRAULIC PRESSURE ...
Rating: 5 · ‎ 1 vote

Where is speed sesor located - 2004 Daihatsu Terios

Fixya https://www.fixya.com > ... > 2004 Daihatsu Terios
May 8, 2014 - The speed sensor is located on the side of the gearbox case. It should require one bolt to be removed, and it's wiring decoupled, and 'pop' it ...

Daihatsu Terios transmission speed sensor replacement

AutoGuru https://www.autoguru.com.au > ... > Daihatsu > Terios
When do Daihatsu Terios transmission speed sensors need to be replaced? The transmission speed sensor, sometimes called a vehicle speed sensor (VSS) is ...

Missing: 2004 ‎ Input ‎ turbine

P0715 OBD-II Trouble Code: Input/Turbine Speed Sensor ...

YourMechanic https://www.yourmechanic.com > Articles
P0715 means the transmission will not be able to read the engine RPMs to shift properly causing transmission to shift hard or erratic.

Missing: Daihatsu ‎ Terios.

..

it is a sensor that measures the speed of the shaft of the converter into the transmission so it will be at the front of the box
it will be as per the workshop manual

Turbine Speed sensor is the input sensor.

that is the input/turbine speed sensor circuit malfunction. or turbine shaft speed sensor. it tells the car when to shift.

I hope this helps and is what your looking for... good luck

http://www.fordobdcode.com/p0715-ford

Ford P0715 OBD-II Trouble Code Definition:
P0715 Input Shaft Speed Sensor Circuit Malfunction
P0715 Ford OBD-II Trouble CodeDescription:
OBD Trouble Code P0715 Input/Turbine Speed Sensor "A" Circuit What does the code mean? OBD-ii Code P0715 definition:
The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM). Symptoms Sumptoms of OBD code P0715
- Engine Light ON (or Service Engine Soon Warning Light) - Possible shifting problems Causes Causes of the OBD-II code P0715
- Transmission speed sensor circuit is open or shorted. - Poor transmission speed sensor circuit connection - Faulty transmission speed sensor The Error code is generally activated on detection of the following conditions: Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the sensor. Solutions

Did the overcharge or voltage regulator problem go away with the new ECM in it? If so the transmission code.. (turbine speed sensor input) code is probably another problem that the Jeep has.. and the ECM will not fix that, but the input speed sensor that it may need is not very expensive.

the is also known as sensoer c it is your pressure control solenoid. if you drop the transmission pan and remove the transmission filter it is on the side of the valve body. DO NOT REMOVE THE VALVE BODY PLEASE

no
a vehicle speed sensor ( VSS) reports on the vehicle speed to the ECM, speedo and TCM
the turbine speed sensor reports on the input shaft speed so that the TCM knows when to change ratios against the VSS reports
the sensor is readily available from dealer spares , transmission shops , e-bay or the wreckers / junk yards
talk with an accredited transmission specialist shop

Transmission Input Speed Sensor (G182 VAG com code): Circuit Malfunction
The Input Turbin Speed Sensor is located inside the transmission, the code can be caused by a failed sensor or sensor wiring or a slipping transmission.

I can tell you what the codes are but I afraid I don't have an answer as to how to fix it.
700 - Transmission Control System Malfuntion
715 - Input/Turbine Speed Sensor Circuit Malfunction
731 - Gear I Incorrect ratio
733 - Gear 3 Incorrect ratio
734 - Gear 4 Incorrect ratio