I am unable to enter the number 9 on my chrysler radio code as there are only numbers1-5 on the controls

it should be in your manual or service book you enter the 4 digits into radio buttons mine is grand voyager i use cd button numbers enter 4 digit code the radio should them come on if you dont have manual ring chrysler might be able to get code off your vin

The wrong code... you can get the right one here:


https://www.carstereocode.com/unlock.php?mk=8

When you disconnect your battery and then reconnect it again, it disables the radio. This is an anti-theft protection for your car radio.
The enable your radio the activation code is in your vehicle owner's manual. If you do not have this code you need to go to your Chrysler service centre and get them to enter this code for you.

Hello Camille, you will need the code for the radio, if you don't have it, look in the trunk, VW likes to hide them in there, under the spare tire. If you can't find it, you will have to get it from the dealer per VIN number. Once you have the code follow this procedure.

1: Turn on the radio, "SAFE" will appear in the display
2: After 3 seconds, the number 1000 will appear in the display.
3: Use the radio station preset buttons 1 to 4 to enter the code number for your radio. Use preset button 1 to enter the first digit in the code number. Use button 2 to enter the second digit, etc. The value range for each of the 4 digits is "0...9". The digit will increase by 1 each time you tap the preset button. The number returns to "0" after "9".
4: After you finish entering the code, press the right side (">") of the SEEK button 10 for longer than 2 seconds until you hear an audible signal.
5: if you`ve entered the code number correctly, "LSM" will appear in the display.
6: Now you are ready to use the radio again.

I hope this information is helpful.

Perform the steps in exactly the following order:
1. Turn on the Radio. "Safe" will appear in the display.
2. After 3 seconds, the number "1000" will appear in the display.
3. Use the radio station preset buttons 1 to 4 to enter the code number found on your Radio Card. (which was in the first page of Sound manual )
Use preset button 1 to enter the first digit in the code number. Use button 2 to enter the second digit, etc. The value range for each of the 4 digits is "0-9". The digit will increase by 1 each time you tap the preset button. The number returns to "0" after 9".
4. After you finish entering the code, press the right side (">") of the SEEK button for longer than 2 seconds until you hear an audible signal.
5. If you have entered the code number correctly, "LSM" will appear in the display. (It just was the radio channel indicator and then everything was working as usual).

Hello! If the battery has been disconnected and the radio was not changed the system will clear on its own...It takes 1 hour, with the radio on, to reset itself...However, here is the procedure...

1. Turn on the Radio... "Safe" will appear in the display...
2. After 3 seconds, the number "1000" will appear in the display....
3. Use the radio station preset buttons 1 to 4 to enter the code number...
Use preset button 1 to enter the first digit in the code number. Use button 2 to enter the second digit, etc... The value range for each of the 4 digits is "0-9"... The digit will increase by 1 each time you tap the preset button... The number returns to "0" after 9"...
4. After you finish entering the code, press the right side (">") of the SEEK button for longer than 2 seconds until you hear an audible signal...
5. If you have entered the code number correctly, "LSM" wlll appear in the display...

If you entered a wrong code number, "SAFE" will appear in the display... Initially it'll flash, then stay on...

You can repeat the procedure again one time...If the wrong code number is entered again, the unit will be disabled for 1 hour... Leave the unit on and the key in the ignition...

Guru......Saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

AR82.60-P-7502-01A Coding Radio
(MODEL all with CODE (750) Radio Becker Europa 2000 with CODE (751) Radio Becker Grand Prix 2000 with RDS)

1. If the radio is disconnected from the power supply, it is not operational when re-connected. After switching on the ignition and the radio, the readout CODE appears in the display.
2. The code number for the radio is advised to you on the enclosed CODE CARD.
3. To enter the first digit of the code number, you have to continue pressing station button 1 until the correct digit appears in the display. Adopt the same procedure for the second, third and fourth digits.
4. Once you have entered the correct code number with the station buttons 1, 2, 3, 4 and confirmed the entry with the SEEK button (press down), the readout CODE disappears. The radio can now be operated.
5. If you enter a wrong code three times, you must wait 15 minutes before making a new entry. In addition, if 9 incorrect entries are made, the radio will then not operate for 24 hours. During this time the radio and the ignition (terminal 15) must remain switched on.

AR82.60-P-7502-01B Coding Radio
(MODEL all with CODE (353) Audio 30 APS with CODE (510a) Radio MB Exquisit with traffic news decoder, with RDS (Becker) with CODE (512a) Radio MB Special with traffic news decoder, with RDS.)

1. If the radio is disconnected from the power supply, it cannot be operated by simply reconnecting. After switching on the ignition and the radio the word "CODE" appears in the display on the radio.
2. The code number for the radio is given on the enclosed CODE CARD.
3. Enter the code number with the station button, e.g. number 1, station button 1. After entering the first number the word "CODE" disappears and the number entered appears followed by 4 dashes. The next character to be entered flashes. After entering all five numbers, the first character starts flashing again. In this state the code number can be written over as frequently as desired. A correction can be made only by entering the complete code number again.
4. Confirm code number: Press TUNE, AUTO/SEEK or SC button. The radio automatically switches on and indicates the radio station or frequency stored with station button 1.
5. If an incorrect code number is entered and confirmed, the word "CODE" appears again on the display. If an incorrect code is entered three times the word "WAIT" appears on the display and the radio locks up for approx. 10 min. If the code is entered incorrectly three times again the radio locks up again for 10 min. Three more incorrect entries (a total of 9 incorrect attempts) increase the lock-up time to 60 min. Another three incorrect entries lock up the radio for another 60 min. The waiting time runs only when the radio is switched on.

see here  for the Neon 2001 - 2008 

http://www.torbaycarstereo.co.uk/chrysler_p05091610ab.html

or if not try here

http://www.radio-code.co.uk/code-entry-help-Chrysler.htm

you do not have a number 9 in the radio code. the radio code was on a small white sticker and there was 3 copies of it when the auto was shipped to the dealer. If you have a navi system in the car that may be the navi code that you are looking at. If you cannot find your radio code you will have to contact your dealer and he will want the serial # for the radio. Turn the radio off and press and hold the #1 and 6 buttons. Now press the power button. You have entered the self diagnosis of the radio. press the #2 button and it will give you the serial #. Press it again and you can temp. listen to your radio. The radio will fail after 3 attempts. Pull the neg. cable off the battery and start over.