Question about 2002 Toyota Sienna
Here is the procedure from the service manual. I would add just one thing. Do each wheel in this order
HINT: If any work is done on the brake system or if air in the brake lines is suspected, bleed the air from the system.
NOTICE: Do not let brake fluid remain on a painted surface. Wash it off immediately.
a)FILL BRAKE RESERVOIR WITH BRAKE FLUID Fluid:SAE J1703 or FMVSS No. 116 DOT3
b)BLEED MASTER CYLINDER HINT: If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.
c)Disconnect the brake lines from the master cylinder. SST 09023-00100 Slowly depress the brake pedal and hold it.
Block off the outlet plug with your finger and release the brake pedal.
Repeat (b) and (c) 3 or 4 times.
BLEED BRAKE LINE
1. Connect the vinyl tube to the caliper or wheel cylinder bleeder plug.
2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down.
3. At the point when fluid stops coming out, tighten the bleeder plug, then release the brake pedal. Torque: (Bleeder plug) Front brake caliper
: 8.3 Nm (85 kgf-cm, 74 inch lbs.) Rear wheel cylinder: 8.5 Nm (87 kgf-cm, 75 inch lbs.)
4. Repeat (b) and (c) until all the air in the fluid has been bled out.
5. Repeat the above procedure to bleed the air out of the brake line for each wheel.
CHECK FLUID LEVEL IN RESERVOIR Check the fluid level and add fluid if necessary. Fluid: SAE J1703 or FMVSS No. 116 DOT3
Posted on Jun 25, 2010
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: front brakes 2008 toyota sienna
No special tools needed, just a 17mm, 21mm. I do not recommend people without training do their own brakes, it is too dangerous to risk peoples lives just to save a few bucks. Also, any pads other than Toyota's will make noise and squeal, so if noise will bother you, use Toyota pads and resurface the rotors.
Posted on Feb 18, 2009
No special tools at all. Are you familiar with doing brakes? I wouldnt recommend it for a first timer, its not worth the lives of you and others. Ive also seen people take the wrong bolt out of calipers and spend triple what a brake job cost because they werent experienced and wanted to save a buck. A 17mm and pad spreader or big channel locks is all you need. Use Toyota pads and have the rotors cut..OR... Dont complain when they make noise all the darn time!
Posted on Jan 25, 2009
Being 2002, its probably has original feon in the systems, you sysytem may be low and needing recharging, recharge the sysytems will tell you exactly what your problems is. If your compressor is not kicking on, mean you either low on feon Or the presure swicth may be faulty, if not than it would be your compressure, ect....., have it rechage first before anything, that may solve your problems..if the system is low on feon the systems will not run period.
Posted on Aug 13, 2009
I had transmission fluid drain and fill last year and had not driven more than 6K since the transmission fluid replacement andfound out that the fluid color getting dark.
My question is now how I should change it now, should it be completely flush or regular drain. I have heard that complete flush makes the transmission seals weak, that is why not recommended, is that true
Posted on Apr 05, 2011
Tips for a great answer:
Nov 13, 2017 | Toyota Cars & Trucks
Feb 17, 2017 | 2002 Toyota Sienna
Dec 06, 2015 | Toyota Cars & Trucks
Sep 19, 2015 | 2002 Toyota Sienna
May 02, 2014 | 2004 Toyota Sienna
Jul 24, 2011 | 2001 Toyota Sienna
Mar 28, 2009 | 2008 Toyota Sienna
Nov 04, 2016 | 2002 Toyota Sienna
3,366 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: