Question about 1993 Geo Tracker

1 Answer

My 1993 Geo Trackers has no turn signals, replaced the steering column figuring it was the turn signal switch. Still no turn signals, checked the fuses they are fine, i have lights wipers...etc.. PLEASE HELP ME!!!

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 145 Answers

Check continuance in lamp wiring CHECK CLOCK SPRING ASAP

Posted on Aug 17, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove the ignition lock cylinder from a 93 geo storm


is the lock assembly in the car or out?
there are 2 jobs here, removing the assembly
and after that, attacking the lock it self.???????

any lock smith can rebuild the lock, proper
it has pins that are pressed out.
it can even be rekeyed.

the remove assembly is covered in the FSM, no books?
alldata.com covers that.
it really is an Isuzu. impulse.

my guess is its job 1, assembly out.
so toss coin lands on job1
(on most cars, steering wheel must be removed)
once that is done, its obvious from there, right? that clamp there with the antitamper screws? then must be removed. and replaced new..

a rare car , and even more one that runs....

here is the online FSM answer

  1. Remove the negative battery cable.
  2. Remove the steering wheel.
  3. Remove the combination switch assembly.
  4. Turn the key to the OFFposition, depress the retaining pin and remove the ignition lock cylinder from the switch.
  5. Disconnect the electrical connector from the ignition switch.
  6. Remove the snapring and spacer collar from the steering shaft.
  7. Disconnect the back drive cable from the ignition switch.
  8. Remove the ignition switch bolts and the ignition switch from the steering column.


now back in?
  1. Install the ignition switch to the steering column and tighten the bolts.
  2. Connect the back drive cable to the ignition switch.
  3. Install the spacer collar and the snapring to the steering shaft.
  4. Connect the electrical connector to the ignition switch.
  5. Install the lock cylinder into the switch.
  6. Install the turn signal switch screws and the turn signal switch.
  7. Install the four screws and the coil assembly to the turn signal switch.
  8. Connect the coil assembly wiring harness to the turn signal switch.
  9. Install the two piece steering column cover and the two piece steering column cover screws.
  10. Raise the steering column and install the upper steering column mounting bolts. Tighten the bolts to 18 ft. lbs. (24 Nm).
  11. Install the left lower dash trim panel and tighten the lower dash trim panel screws.
  12. Install the lap air deflector and tighten the lap air deflector screws.
  13. Install the knee pad assembly and tighten the five screws, the bolt and the nut attaching the assembly.
  14. Install the engine hood opener cable.
  15. Install the engine hood opener and tighten the two screws.
  16. Connect the electrical connector to the cigar lighter bezel and install the bezel.
  17. Connect the electrical connector to the left switch bezel and install the bezel.
  18. Install the steering wheel.
  19. Connect the negative battery terminal to the battery.

that?

Oct 08, 2014 | 1993 Geo Storm

1 Answer

How to replace ignition lock cylinder


This may or may not help,but i found this

REMOVE OR DISCONNECT

1. Disable the SIR System.
2. Battery negative cable.
3. Knee bolster and IP steering column reinforcement. NOTICE: The steering column should never be supported by only the lower support bracket alone, damage to the column lower bearing adapter could result.
4. Lower support bracket from vehicle (2 bolts).
5. Upper column support from IP (2 bolts).
6. Lower steering column so that it rests on the driver seat.
7. Ignition switch wiring protector.
8. Ignition switch retaining screw and nut.
9. Ignition and turn signal switch column harness connectors from IP harness.
10. Turn signal switch connector from column harness.
11. Ignition switch, harness, and connector. Important

o DO NOT splice ignition switch wires.

INSTALL OR CONNECT

1. Ignition switch, securing with retaining screws.

o Adjust ignition switch. Steering Column Unit Repair.

2. Turn signal switch connector to column harness.
3. Ignition and turn signal switch column harness connectors to IP harness.
4. Ignition switch wiring protector.
5. Raise steering column to support bracket.
6. Two bolts to upper support bracket. Do not tighten fully at this time.
7. Bolt and nut to lower support bracket.

o Align column to instrument panel opening. A small shim (wedge) placed between the instrument panel column support bracket and the column can be used to hold the column stationary while tightening the upper support bolts.
o Upper and lower column support bolts and nuts to 27 Nm (20 ft. lbs.).

8. IP steering column reinforcement plate and knee bolster.
9. Battery negative cable.
10. Enable the SIR system.
super vag k+can v4.8

Jul 30, 2012 | 1994 Geo Prizm

1 Answer

Turn signal/brights/wiper switch


you have a dimmer switch in the column along with the turn signal and headlight switch
the dimmer switch is usually mounted near the bottom of the column

Jun 28, 2012 | 1993 Buick LeSabre

1 Answer

How do you replace the blinker lever on the steering column of a 1993 Jeep Wrangler?


You will have to remove steering wheel,and lock plate,then remove the turn signal cam,and then there is a screw holding the lever to the turn signal switch.

May 17, 2010 | 1993 Jeep Wrangler

1 Answer

How to replace turn signal switch 93 aerostar van xlt


Take a screwdriver and loosen the screws that hold on the steering column wrap. Separate it, and pull it off. You should see the turn signal switch screws. Replace it and put the column cover back on.

B

Sep 08, 2009 | 1993 Ford Aerostar Extended

1 Answer

Steering column diagram for 1993 s-10 blazer


a haynes manual from the parts store will have that in there. about 20 bucks for the manual.

Jul 20, 2009 | 1993 Chevrolet S-10 Blazer

2 Answers

Turn signals won't come on.


I would have to say that it is your turn signal switch in the column. You will have to take the steering column apart and replace it.

Jun 19, 2009 | 1993 Ford Taurus

2 Answers

I need to locate and replace the multi function switch


My turn signal flasher was located to the right of the ash tray, I looked around the column for HOURS and it wasn't there... I also have an 93 oldsmobile cutlass ciera, it drove me crazy because the manual wasn't correct.

Feb 27, 2009 | 1993 Oldsmobile Cutlass Ciera

2 Answers

Turn signal switch is dead. Not working at all. Not sure where its located to replace the switch


hi how are you? the turn signal switch is behind your steering wheel in the column.must remove horn assembly.then steering wheel,use puller to remove wheel.next remove clip that holds steel plate.(tool required).remove plate.then remove any steering column covers/plastic.then remove screws for turn signal switch.unplug wires and remove.then reinstall in reverse.

Feb 02, 2009 | 1993 Mercury Cougar

1 Answer

Turn signal switches


No.first off remove horn pad in centre of steering wheel and remove steering wheel Do Not hit steering shaft to remove,use puller or wiggle it off.Remove the bottom steering wheel cowl/shroud below steering wheel.Lower the steering column by removing the two torx head bolts located under the dash.Remove the two upper and lower screws that hold the switch to the column.Unplug switch and assembly is reverse of disassembly.Good luck let me know if you need more help

Nov 23, 2008 | 1991 Geo Tracker

Not finding what you are looking for?
1993 Geo Tracker Logo

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...