Ignition coil e

no fuse for coil if no power to coil[s] assuming its the ignition coils sheck and test wiring and coil for damage or failure

Location of ignition coil relay ??????? Doesn't have a relay for ignition coil . Power for it comes from the ignition switch.

Ignition Coils/Modules
The electronic ignition system uses an individual ignition coil for each cylinder. There are two separate ignition module assemblies located in the camshaft cover of each cylinder bank. Each ignition module assembly contains an ignition control module and four ignition coils. Each ignition coil connects directly to a spark plug using a boot. This arrangement eliminates the need for secondary ignition wires. The ignition module assemblies receive power from a fused ignition feed. Both ignition module assemblies connect to chassis ground. A Reference Low and four ignition control (IC) circuits connect each ignition module assembly to the PCM. The PCM uses the individual IC circuits to control coil sequencing and spark timing for each ignition coil. The IC circuits transmit timing pulses from the PCM to the ignition control module to trigger the ignition coil and fire the spark plug. The PCM controls ignition system sequencing and timing events

This is for the 3.0L engine:

3.0L Engine

1. Remove the engine appearance cover.
   
2. To access the right bank ignition coils, remove the upper intake manifold..
   
3. Disconnect the electrical connector from the ignition coils.
   
4. Remove the bolts.
   
5. Remove the ignition coils.
   

To install:

1. Replace the ignition coils.
   
2. Connect the electrical connector to the ignition coils.
   
3. Remove the upper intake manifold for the right bank ignition coils.
   
4. Replace the engine appearance cover.
   

I searched under 'ignition module' on autozone.com and 'no parts for ignition module' turned up.
I looked under DIS or Distributorless Ignition System and found the coils are inserted in the top of the engine and this tells me that it's likely that the ECM or PCM controls the spark on these cars.

Civic
1.7L Engine

1. Disconnect the negative battery cable.
2. Remove the ignition coil cover (A), disconnect the ignition coil connectors (B), then remove the ignition coils (C).
3. Installation of the ignition coils is the reverse of the removal procedure.
   
   

   Fig. Remove the ignition coil cover (A), disconnect the ignition coil connectors (B), then remove the ignition coils (C)
   

Your ignition control module is under the coil packs on the motor.

The plugs are located below the 6 ignition coils. The three front ignition coils are located underneath the plastic engine cover that has the V6 3000 marking on it. The other three coils are located in the same position, in the other engine head, towards the rear of the engine compartment. They don't have a cover over them. You will have to unbolt and unplug each ignition coils to remove it.

Please find the ignition coil location in the picture below

303-07A: Engine Ignition — 3.0L (4V) 2001 Lincoln LS Workshop Manual DESCRIPTION AND OPERATION Engine Ignition The electronic ignition (EI) system is a coil-on-plug (COP) ignition system.
---------------------------------------------------------------------------------------
SECTION 303-07B: Engine Ignition — 3.9L 2001 Lincoln LS Workshop Manual
DESCRIPTION AND OPERATION Engine Ignition The electronic ignition (EI) system is a coil-on-plug (COP) ignition system
-----------------------------------------------------------------------------
v-8
SECTION 303-07B: Engine Ignition — 3.9L 2001 Lincoln LS Workshop Manual
REMOVAL AND INSTALLATION Ignition Coil Removal

1. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 .

1. Remove the bolts and the ignition coil cover.

1. Disconnect the electrical connector from each ignition coil.

1. Remove the ignition coils.
   1. Remove the bolts.
   1. Remove the ignition coils.

------------------------------------------------
v-6

SECTION 303-07A: Engine Ignition — 3.0L (4V) 2001 Lincoln LS Workshop Manual
REMOVAL AND INSTALLATION Ignition Coil Removal

1. Remove the engine appearance cover.

1. To access the RH bank ignition coils, remove the upper intake manifold. For additional information, refer to Section 303-01A .

1. Disconnect the electrical connector from the ignition coils.

1. Remove the bolts.

1. Remove the ignition coils.

please rate as fixed if this helps.

Follow the plug wires back to the coil. This engine does not use "coil on plug" so there is only one coil. If there is a cover on top of the engine, most likely it's under the cover.