Question about 1991 Jeep Wrangler

1 Answer

How do you check the clutch fluid on 1991 Jeep Wrangler?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

There should be a small master cylinder for the clutch right next to the brake master cylinder, mounted more towards the fender. Remove the top cover and look inside. Regular brake fluid is used in the clutch system. If it's low, likely you have a leak so check where the rod goes through the firewall under the dash, the line itself and the slave cylinder (some are outside the bellhousing, others are inside and fluid will leak from the bottom of it.

Posted on Jun 15, 2010

Testimonial: "Found it, thank you very much!!"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 jeep wrangler clutch has to pressure and thus wont allow me to put it in gear.


Check the clutch fluid level. If it's low, add some (takes brake fluid). There is a bleed valve down on the clutch slave cylinder on the bellhousing. Open the bleed valve and have someone push the clutch pedal slowly to floor, and hold. Close the bleed valve, and repeat until fluid comes out in a steady stream when the pedal is depressed. Your pedal should have pressure now, and the clutch should be working.
If no fluid is forced out the clutch master cylinder, into the line, and to the slave cylinder when clutch is pressed, then you may have a bad clutch master cylinder. If fluid does come out the bleed valve, but still no pressure on the pedal, it may be a bad slave cylinder.
Post back for more. Would like to know what you find out, and what the problem was, OB. Good luck.

Jul 13, 2012 | 1991 Jeep Wrangler

2 Answers

I have a 1991 jeep wrangler the clutch fluid keeps getting real low


clutch fluid level droppin means that ur clutch master cylinder is leaking,u can check by looking inside car where pushrod goes thru firewall to see if its wet with brake fluid where rod comes thru wall inside car, a wet ,stained carpet.the other possibility is ur clutch slave cylinder located at side of ur transmission,usually drvr side is leaking fluid.if this is the case u will notice clear brake fluid at the bottom center of ur trans,right where it butts up towards ur engine. anyhow its a good idea to replace both pieces at same time to avoid any further issues with clutch pedal. good luck hope this helps

May 01, 2011 | 1991 Jeep Wrangler

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

1 Answer

1991 jeep wrangler


yes it could be also check the fluid level!

May 14, 2009 | 1991 Jeep Wrangler

1 Answer

1991 jeep wrangler sahara shifting promblems


Your clutch is not disengaging. If it a hydrolic clutch chk. the fluid in resavor, Or slave cyl. for the clutch is bad, Or it has got air in it and needs to be bleed. This is a clutch problem, nothing wrong with trans. If its a manual clutch linkage its an ajustment thing. My best guess if its hydrolic slave cyl. went bad, or resavor is out of fluid.

Feb 10, 2009 | 1991 Jeep Wrangler

2 Answers

1991 jeep wrangler not shifting into gear could this be clutch


I would first bleed the tranny lines, if that doesnt work then your tranny is out and need to get it replaced. FYI with Jeep Wranglers, It is better to get a new transmission then to rebuild them

Feb 09, 2009 | 1991 Jeep Wrangler

1 Answer

Clutch Pedal to Floor


slave cylinder needs replaced

Nov 12, 2008 | 1991 Jeep Wrangler

Not finding what you are looking for?
1991 Jeep Wrangler Logo

Related Topics:

596 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...