2000 Mazda 626 Logo
Posted on Jun 14, 2010
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Looking for the location of crank shaft on 2000 mazda 626

Looking for location of crank shaft for 2000 mazda 626

1 Answer

Colin Stickland

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Mazda Master 22,516 Answers
  • Posted on Jun 14, 2010
Colin Stickland
Mazda Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Nov 04, 2008
Answers
22516
Questions
3
Helped
6991648
Points
66324

I assume you mean crank shaft sensor ,if its not on the front puilley then look around the bell housing in the most extreme awkard in accessable position possible because you can bet that is where it is

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

I need picture showing me where my transmission filter is for 2000 mazda 626 4cyl

try autozone library ,most cases its located on the lowest portion of tranny that is automatic , when at auto zone look up the part tranny filter and it will show you what it looks like
0helpful
2answers
0helpful
1answer

Where is the fan relay switch located on the 2000 Mazda 626?

Power distribution box in the engine compartment ,black box there's up to 3 relays for cooling fan
1helpful
1answer

I have a 2000 Mazda 626 4 cylinder and the crank shaft went do I replace it or get a whole new engine.

you will be better off with a remanufactured or low mileage used engine.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

0helpful
1answer

My 2000 mazda 626 cranked on its own can't found problem to it cut-off

Hello your starter relay switch look under hood at the power distribution box beside battery open see diagram for relay remove the starter relay switch the starting on it's own will cut off and stop.Sometimes these relays stick you might consider changing it or trying a another used one.
0helpful
1answer

626 stuck in reverse.

look down on top of the transmission you should see a flat lever, just click it until u are in neutral
1helpful
1answer

2000 mazda 626 fuel filter location.engine sputters at 55-60 mph

it should be on the driver side. very hard to get to. look under the air box were the air filter goes.
j.aguilar
0helpful
1answer

Mazda 626 with no spark

be for you dig to deep into something like that take off the distributor cap and then pull off the rotter and check your connection at that point. that part might have to be changed
1helpful
1answer

Mazda 626

Hi Janieanip01,
Again we need more imfo....Is the vehicle injection?....If it is you'll have to wait until the fuel rail is re-pressurised before it will start....Crank it for about ten seconds at a time so as not to burn out the starter motor....It may be that the vehicle didn't run out of fuel but instead the pump may have given in....and when did you last replace the fuel fiter?
Regards Johngee10
Not finding what you are looking for?

277 views

Ask a Question

Usually answered in minutes!

Top Mazda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...