Question about Cars & Trucks

1 Answer

Just scanned my 1999 300m. It went into safe mode while me wife was driving it home- 2nd gear only. It had a code P1714 and P0700 come up on the scanner. I can't find anything about the P1714.

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 666 Answers

Definition of Diagnostic Trouble Code P1714 Chrysler: Low Battery Voltage Dodge: Low Battery Voltage Ford: Shift Solenoid A Inductive Signature Jaguar: Shift solenoid A inductive signature malfunction Jeep: Low Battery Voltage Lincoln: Shift Solenoid A Inductive Signature Mazda: Shift Solenoid '1' Mechanical Fault Mercury: Shift Solenoid A Inductive Signature Subaru: Throttle position sensor power circuit for automatic transmission
Definition of Diagnostic Trouble Code P1714 Chrysler: Low Battery Voltage Dodge: Low Battery Voltage Ford: Shift Solenoid A Inductive Signature Jaguar: Shift solenoid A inductive signature malfunction Jeep: Low Battery Voltage Lincoln: Shift Solenoid A Inductive Signature Mazda: Shift Solenoid '1' Mechanical Fault Mercury: Shift Solenoid A Inductive Signature Subaru: Throttle position sensor power circuit for automatic transmission
Definition of Diagnostic Trouble Code P1714 Chrysler: Low Battery Voltage Dodge: Low Battery Voltage Ford: Shift Solenoid A Inductive Signature Jaguar: Shift solenoid A inductive signature malfunction Jeep: Low Battery Voltage Lincoln: Shift Solenoid A Inductive Signature Mazda: Shift Solenoid '1' Mechanical Fault Mercury: Shift Solenoid A Inductive Signature Subaru: Throttle position sensor power circuit for automatic transmission
That code is low battery voltage on a chrysler

Posted on Jun 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 05 Pacifica went into "limp in" mode which means it is stuck in 2nd gear. I took it to AutoZone and put it on the code machine. It pulled up P0700, P0715, P0731 and P0733. I changed out hte Speed Sensor...


Well code 700 is a generic code that means there is a problem with the transmission or the control module. Code 731 is for a problem with first gear which would explain why it stays in second gear.
Someone will need to check the circuits involved with first gear and the trans control module. A shop manual will be necessary to get the testing procedures.

Jul 30, 2013 | 2004 Chrysler Pacifica

1 Answer

I was driving my 2004 dodge sx 2.0 (automatic) when all of a sudden i lost the drive gear so i by instint droped it down in to third and still no response... So i pulled over to the side of the road and...


The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM. This code is for information ONLY. If this code is present, check for transaxle codes. So basically, the P0700 code is telling you to check the TCM for a transaxle DTC. The TCM can not turn on the check engine light so it has the PCM do it. The dealer probably saw the code P0700 and went to the TCM and pulled out the code stored there telling them the Transmission Solenoid Assembly (TSA) is bad.

Jul 11, 2011 | 2004 Dodge Neon

1 Answer

1996 Jimmy only 2nd gear any suggestions?


YOUR TRUCK TRANSMISSION IS IN A "DEFAULT MODE" GIVING YOU SECOND GEAR ONLY TO PROTECT FROM DAMAGE DUE TO AN ELECTRICAL OR MECHANICAL FAILURE AFFECTING YOUR TRANSMISSION, YOUR WILL NEED TO PLUG IN A ENGINE CODE SCANNER TO RETRIEVE SOME COMPUTER FAILURE CODES, CODE YOUR WILL BE LOOKING FOR START WITH A P0700 ON UP, BUT DO NOT IGNORE ANY ENGINE FAILURE CODES, GENERAL REPAIRS PROCEDURES REQUIRE THAT THOSE BE REPAIRED FIRST.!. SCAN YOUR VEHICLE AND RE-POST THEM BACK, I WILL HELP YOU FURTHER.

Jul 01, 2011 | 1996 GMC Jimmy

1 Answer

Car wont shift from 2nd gear and speedometer doesnt work. diagnostic code p0700. what does this mean?


the PO700 code is a generic transmission code. You would need access to a proper scan tool to check for transmission codes. However if you speedo isnt working, it sounds as though you have a bad output speed sensor. This part runs about 60.00 from the dealer, and is fairly easy to install. No speed signal will put the transmission into limp mode, and keep it stuck in 2nd gear.

Nov 17, 2009 | 2000 Chrysler 300M

1 Answer

I have a 2000 Dodge Grand Caravan. Lastnight my


Darrell, The trans went into limp mode. 41te trans do funny things. The limp setting is so you can get home or to the dealer. As for the slipping , check fluid first. If ok scan for codes from trans...

Oct 07, 2009 | 2000 Dodge Caravan

2 Answers

1999 concorde. in limp mode with check engine


you should also replace the input speed sensor,they should always be done in pairs and i have had both of them bad on numerous vehicles,hope this helps

Sep 09, 2009 | 1999 Chrysler Concorde

1 Answer

2005 Dodge Neon SXT error code P0700


you have a output speed sensor going out probley the tranny is in lemp mode and is stuck in 2nd gear

Jul 24, 2009 | 2005 Dodge Caravan

1 Answer

1994 F350 transmission intermittent problem


I had the same problem in my 96 f-350. The transmission has slipped recording a slip code in the transmission. You can pull the codes and get it. I shifts into a safe mode that increases the pressure inside your transmission as part od a fail safe. Plain and simple, you have to have the tranny rebuilt.

Dec 06, 2008 | 1994 Ford F350 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,285 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22406 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...