Question about 1993 Chevrolet Camaro

1 Answer

How do i flush the hydraulic steering system - 1993 Chevrolet Camaro

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 3,854 Answers

You really can't flush out the steering system fluid other then siphoning the fluid out of the steering pump reservoir. This is the easy way.
The hard way:
Remove the filler cap from the top of your power steering system then disconnect the reservoir's hose. It should be located on the bottom of the reservoir. The hose can be tough to remove, so make sure you have plenty of patience.

Replace the reservoir's hose with another hose. It should lead to an empty container. You'll use this container to store the old power steering fluid as it leaves the reservoir. Lift the front end of your car off the ground by using a car jack.

Add new power steering fluid to the reservoir. As you add the new lubricant, it will force the old lubricant into the tube you've connected to the bottom of the reservoir.

Climb into the drivers seat and rack your steering wheel back and forth. The wheel should be locked in place, allowing only a slight range of mobility. This will help the extra lubricant within the power steering system to drain.

Watch the empty container. It should fill with old lubricant. Once the old lubricant has been flushed and you see clean fluid replacing it, you've finished the hard part.

Disconnect your hose and move the container. Replace the original reservoir hose. Pour new, clean power steering fluid into the reservoir. Rack your steering wheel a few more times to squeeze out air that might be trapped in the lines. Replace the filer cap and close your done.

Thank you for suing fixya and good luck







Posted on Jun 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My malibu 2003 keeps breaking while im driving. if i stop the break wont release from the front tires and the car starts heating up..


The described braking concern is symptomatic of contamination in the brake fluid. When oil comes in contact with the O rings/seals in the hydraulic brake system, the neoprene material will swell up and restrict movement of the brake caliper pistons. The caliper pistons will move out against the disc brake pads, but due to the distorted O ring seal, it will not retract while the brake pedal is released. Sometimes, the service person at the oil change station will by mistake put power steering fluid in the master cylinder reservoir and create the symptom. If you find this to be the case, the entire hydraulics system will have to be flushed or replaced and all of the neoprene (rubber) components will have to be replaced. If you do all the underhood service on your car, then you don't have to look very far to discover who put power steering fluid in the brake cylinder

Aug 08, 2018 | Cars & Trucks

Tip

Flush Brake Fluids and Power Steering Fluids Economically


Many vehicle maintenance schedules require flushing of BRAKE FLUIDS, as well as HYDRAULIC POWER STEERING FLUIDS. An inexpensive way to do this yourself is to go out, and buy 2 TURKEY BASTERS. Mark each separately, one P/S and one Brake Fluid. DO NOT INTERCHANGE. As per maintenance schedule, siphon brake fluids from MASTER CYLINDER, ( recycle properly ) and replenish with fresh , clean fluids, Do the same with the power steering fluid in the pump. Of course you won't be removing all of the fluids, but a sufficient amount will be replaced. You can do it 2x after running if so inclined.

on May 08, 2009 | 1993 Cadillac DeVille

1 Answer

Hydraulic system/power steering unit needs flush on ford fairlane 2006 G8


crack open the large nut on your pipe on your rack .and drain it from there.do not take off .just crack it open to drain.then close the nut and refill .

Dec 06, 2013 | Cars & Trucks

1 Answer

Somehow water is getting into the hydraulic fluid on the power steering system. this can be seen when taking off the cap on the pump, and checkinig the fluid level. There will be rusty brown water f


replace power steering fluid with new fluid bleed system sound like you have air trapped in the system.replace fluid and bleed system see what happens.

Nov 18, 2013 | Ford Aerostar Cars & Trucks

1 Answer

I was told that the Golf power steering requires special power steering fluid, not the universal hydraulic power steering fluid. Is that right. After I added regular hydraulic fluid, the steering is very...


I hope you don't have permanent damage from using the wrong fluid. There are several different types of power steering fluid and they are not necessarily compatible. I would have a shop flush the system and refill with the specified fluid.

Apr 03, 2011 | 1998 Volkswagen Golf

1 Answer

HOW TO FLUSH POWER STEERING FLUID


Firstly, get the proper power steering fluid that is meant for your car (some cars use power steering fluid, some use ATF, while others use hydraulic fluid...be sure to use the right one meant for your vehicle!!).

Secondly, get a clean turkey baster, with the car off, **** out the old fluid using the turkey baster and dispose of properly. Fill fluid to proper fill line on power steering reservoir bottle. Then start the car and run it for a couple of minutes while turning the steering wheel gently lock to lock and centering the wheel before shutting it off.

Third, repeat second step until fluid being sucked out matches or is VERY close to the clean fluid being put in.

Fourthly, clean up any spilled fluid thoroughly, as it may cause stains and or a fire hazard.

Fifthly, you are all done....should take you about 10-15 minutes entirely to do a proper flush of the power steering system.

Nov 26, 2010 | 2005 Infiniti Q45

1 Answer

2000 H1 suddenly steering locked up while moving. very difficult to turn with engine on , will turn smoothly with wheels up and engine off. Brake is hard and feels like bubbles underfoot when applied ....


Good day. Please check that all fan and V bellts are in place. Your power steering pump runs with a belt, and the brakes could be of the hydraulic type. Check your power steering pump for failure if all else fails. Hope this helps

Aug 17, 2010 | 2004 Hummer H1

1 Answer

Changing power steering pump


Power steering pump special tools

519a4ae.gif
Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Remove the alternator.
  5. Drain and remove the radiator coolant recovery reservoir.
  6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  7. Remove the idler pulley from the power steering pump support.
  8. Remove the belt tensioner.
  9. Remove the bracket mounting bolt located under the belt tensioner mounting.
  10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  11. Clamp the pump support bracket in a suitable vise.
  12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.

To Install:
NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.

  1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
  4. Install the bracket mounting bolt located under the belt tensioner mounting.
  5. Install the belt tensioner.
  6. Install the idler pulley to the power steering pump support.
  7. Connect the hydraulic pressure and return lines.
  8. Install the radiator coolant recovery reservoir.
  9. Install the alternator.
  10. Install the accessory drive belt.
  11. Fill the power steering reservoir with power steering fluid.
  12. Connect the battery ground cable.
  13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.

Jun 28, 2009 | 1999 Ford Taurus

Not finding what you are looking for?
1993 Chevrolet Camaro Logo

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

84966 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...