Question about 1991 Mitsubishi Mighty Max

1 Answer

1991 mighty max, 5 speed manual ... when going up a hill, motor seems to race as if clutch is slipping, only symptom, no noise, no smell. once truck has been run, does not do this .... truck has 94,000 miles on it. Othersise is ok ... just noticed this problem in the last week or so ... the clutch pedal is 1/2 inch higher than the brake pedal.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 976 Answers

If it has a cable for clutch you need to adjust it. if its hydralic then the master cylinder may be not bleeding off properly when cold or slave sticks when cold. you need to measure pedal free play that is how far pedal goes down before resistance is felt there needs to be 1/2 to 1 inch or so free play to make sure that the release bearing isnt riding on the pressure plate [would be the same as riding the clutch] the 1/2 inch higher than brake pedal probem can be adjusted on the pedal stop but shouldnt be the problem. of course the clutch could be just plain worn out to.

Posted on May 18, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque for installing the crankshaft for the 2.4 mitymax motor?


Mitsubishi Mighty Max crankshaft bolt Questions & Answers ...

www.fixya.com > ... > crankshaft bolt > Cars & Trucks > Mitsubishi
Mitsubishi Mighty Max cars & trucks crankshaft bolt questions and answers. ...Torque specs for mighty max The head torque specs for 1991 mitsubishi mighty max 2.4 I ... 1989 mitsubishi 2.0 motor crankshaft was turned while timeing belt was off. ...how to install a clutch kit on my 1994 mitsubishi mighty max Disconnect the .

Oct 02, 2015 | Cars & Trucks

1 Answer

Celica 5 speed 2001 with only 59,000 miles top speed is 78 mph and it seems engine is at the max RPM's any idea on what's going on?


Hi Mr. Rauscher.
As I understand if correct,and your vehicle is Manual Gearbox,most probably you might have slipping Clutch,if it is Automatic Gearbox again you might having slipping hydraulic clutches. Ask for a test drive from your mechanic

Apr 03, 2014 | Cars & Trucks

1 Answer

I need to change fluid in my manual transmission, not sure how much after a complete drain.


you need to check the level first and make sure that its not leaking anywhere

Nov 29, 2011 | 1995 Mitsubishi Mighty Max

1 Answer

Will a chevy s-10 motor work in a 85 mitsubishi mighty max


Not without using the chevy transmission (and transfer case if it's a 4WD Mighty Max), Custom Motor Mounts, Custom Transmission Mount, Wiring Modifications, Driveshaft Modifications (either lengthened or shortened, depending on where the transmission or transfer case is located). Possibly shifter hole modifications (if it's a 5-Speed Manual), or Custom Linkage/Linkage Modifications (If it's an Automatic)

Aug 21, 2011 | 1985 Mitsubishi Mighty Max

1 Answer

Burning smell whenever i pull off, go up steep hills or simply reverse up my drive


1) Check the brake pads all round. If a caliper is sticking (not retracting fully) then the pad will remain in contact with the disc rotor and gets very hot giving off burning smells. 2) If you have a manual transmission it could also be that your clutch is at the point of failing. A slipping clutch is indicated in gear the engine races irrespective of the the car accelerating along with a smell of burning.

Jun 16, 2011 | Renault R5 Cars & Trucks

1 Answer

I have a 1988 Mitsubishi mighty max pick up 5 speed manual trans. Recently a clanking sound has been coming from the bottom of my truck off and on only when I shift. I thought it was the transmission mount...


check clutch cover or replace, clutch lining or replace, release bearing or replace, pilot bearing or re place, primary clutch repair kit or replace, secondary clutch repair kit or place new one,. check cross joint

Apr 03, 2011 | 1988 Mitsubishi Mighty Max

1 Answer

1991 mitsubishi mighty max want start in cold weather but will when its warm outside what could be the problem?


if this is carb motor than it needs a manual choke that mounts on inside of lower dash, the kind you see on lawn mowers,,,push and pull.

Mar 11, 2011 | 1991 Mitsubishi Mighty Max

1 Answer

Torque specs for mighty max


Per my Chilton's manual tehe bolts should be (cold engine) 65 to 72 FT. Pnds., the cam shaft bearing bolts should be 8x25 = 15 - 19 Ft pnds and the 8x65 should be 14 - 15 Ft Pnds.

The sequence is as follows for the (10 ) head bolts:

7 - 5 - 2 - 4 - 10

9 - 3 - 1 - 6 - 8

I hope this may help,
Tom

Oct 12, 2009 | 1991 Mitsubishi Mighty Max

1 Answer

1991 Mitsubishi Might Max Timing Belt


timing chain when you get a variance in timing easy to see with a timing light haynes manual should be sufficient

Jul 21, 2009 | 1991 Mitsubishi Mighty Max

1 Answer

Rough vibration up hill...


check motor and trans mounts.

Feb 02, 2009 | 1984 Honda Civic

Not finding what you are looking for?
1991 Mitsubishi Mighty Max Logo

305 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...