MBZ 1984 300D Driver side front window & passenger rear

The following components are used to control the power windows:
• Driver door module (DDM)
• Passenger front door module (PDM)
• LH rear door module (LRDM)
• RH rear door module (RRDM)
• Driver door switch assembly (DDSA)
• RH front power window switch
• LH rear power window switch
• RH rear power window switch
• LH front power window motor
• RH front power window motor
• LH rear power window motor
• RH rear power window motor
• Class 2 serial data link
• DR MOD PWR C/B 30 Amp circuit breaker
• DRIVER DR MOD 10 Amp fuse -- DDSA and DDM logic, DDM internal driver operation.
• PSGR DR MOD 10 Amp fuse -- PDM logic and internal driver operation.
• REAR DR MOD 15 Amp fuse -- LRDM and RRDM logic and internal driver operation

Check a wiring diagram an check power an ground for those systems . Also read factory service information on how they work . Electronic modules involved . DDM - driver door module . If this vehicle came to my shop , first thing I do , hook up factory scan tool an check input data from the door switch to the DDM . Check DTC'S - diagnostic trouble codes .
The power windows system consists of the following components:
• Driver door module (DDM) -- GMLAN device that receives and transmits messages and signals for window functionality
• Passenger front door module (PDM) -- GMLAN device that receives and transmits messages and signals for window functionality
• Left rear door module (LRDM) -- GMLAN device that receives and transmits messages and signals for window functionality
• Right rear door module (RRDM) -- GMLAN device that receives and transmits messages and signals for window functionality
• Driver door switch assembly (DDSA) -- GMLAN device that contains the driver, front passenger, RR and LR window and window lockout switches
• Right front power window switch -- provides switched ground window switch signals to the PDM for the front passenger window
• Left rear power window switch -- provides switched ground window switch signals to the LRDM for the left rear passenger window
• Right rear power window switch -- provides switched ground window switch signals to the RRDM for the right rear passenger window
• Left front power window motor -- contains position sensors and a module that receives signals from the DDM and provides a status signal to the DDM
• Right front power window motor -- contains position sensors and a module that receives signals from the PDM and provides a status signal to the PDM
• Left rear power window motor -- contains position sensors and a module that receives signals from the LRDM and provides a status signal to the LRDM
• Right rear power window motor -- contains position sensors and a module that receives signals from the RRDM and provides a status signal to the RRDM
• DRIVER DR MOD fuse (10-amp)
• FRT PASS DR MOD fuse (15-amp)
• REAR DR MOD fuse (10 amp)
• Power Window Motors Circuit Breaker (30-amp)

Your best bet , take it to a qualified repair shop.

Did the switch work before replaced battery ? 2008 CTS ? Cadillac ? These switches are inputs to a control module , DDM - driver door module . a computer of sorts . A lot of thing's can go wrong with these systems , broken power or ground circuits inside the rubber boot from the body to the driver door . Communication problems between control modules etc... Plus the power windows don't use fuse's , has a circuit breaker for front windows - PWR/WNDW circuit breaker 25 amp located in the fuse box under the back seat , Fuse's are used for rear windows - two 15 amp fuse's LT/REAR an rear ,both are in the rear fuse box under back seat. These rear windows are controlled by the BCM - body control module .

The power windows system consists of the following components:
• Driver door module (DDM)--GMLAN device that receives and transmits messages and signals for window functionality. The DDM contains the driver door switch (DDS) which is integrated into the module. The DDS contains the driver, front passenger, RR and LR window and window lockout switches.
• Passenger front door module (PDM)--GMLAN device that receives and transmits messages and signals for window functionality. The PDM contains the front passenger door switch (PDS) which is integrated into the PDM. The PDS contains the front passenger window switch.
• Left rear power window switch--Provides switched voltage and ground window switch signals to the left rear window motor for left rear passenger window operation
• Right rear power window switch--Provides switched voltage and ground window switch signals to the right rear window motor for right passenger window operation
• Left front power window motor--Contains position sensors and a module that receives signals from the DDM and provides a status signal to the DDM
• Right front power window motor--Contains position sensors and a module that receives signals from the PDM and provides a status signal to the PDM
• Left rear power window motor--Contains position sensors and a module that receives signals from the left rear power window switch
• Right rear power window motor--Contains position sensors and a module that receives signals from the right rear power window switch
• DRIVER DR MOD fuse (15-amp)
• PDM fuse (15-amp)
• PWR WNDW Circuit Breaker (25-amp) -- front
• LT/REAR/WNDW fuse (15-amp) -- rear
• REAR/WNDW fuse (15-amp) -- rear


Power Window Operation
The driver and front passenger doors are equipped with power window motors that contains its own module. Each power window motor receives a hot at all times battery supply voltage and constant ground source. When the right front passenger window switch on the DDS is activated to the up or down position, the DDM will interpret the signal and send a GMLAN serial data message to the PDM. Upon receipt of the message, the PDM will send a signal to the front passenger window motor module on the GMLIN serial data circuit. The window motor module will then supply battery voltage and ground to the window motor to drive the window motor to the up or down position.
The DDM communicates via the GMLAN serial data circuit with the body control module (BCM) to control the rear window functions from the driver master window switch. The BCM is hard wired to each rear power window switch with circuits for window up, window down, and an enable circuit. The rear window switches contain internal logic that when supplied with voltage from the BCM over the enable circuit will driver the appropriate window in the direction commanded.
The rear power window switches are supplied with battery voltage from individual right and left WNDW fuses located in the rear fuse block. When a rear power window switch is activated to the DOWN position, voltage is applied to the motor down circuit and the motor up circuit serves as the path to ground. The window motor will drive in the downward direction until the switch is released or the window has fully opened. When the window switch is activated to the UP position, voltage is applied to the motor up circuit and the motor down circuit serves as the path to ground. Ground for the left rear power window switch is supplied at G200 and the right rear power window switch receives ground at G201.

The power locks work the same .

After replacing the driver door switch (DDS) or passenger door switch (PDS), perform the programing procedure.

If you don't know any of what i posted your best bet , have a qualified repair shop check it out .

Window regulator is bad in the drivers door . Do you know what a regulator is ? The Trainer 24 Power Window Troubleshooting Do you know anything about automotive electrical testing ? How to read an use a wiring diagram ? Do you know there are two side to a electrical circuit ? B+ voltage an a ground side . Plus there is electronic control modules and class 2 serial data network involved . When you push the switch for a window othen then drivers window on the drivers door . a class 2 message is sent to the other doors modules . The correct module will then open it's window .
http://www.bbbind.com/free_tsb.html Check out free wiring diagram here .Enter vehicle info . year , make , model and engine size. Under system click on body & accessories , subsystem click power windows . Click search button , then click each link one at a time .

Look at the body control module.

Driver side: 24"
Passenger: 20"
Rear: 16", although I use 18-20 for better coverage

Passenger side: 20" ; Driver's side: 24" GK



At 2001 Windstar all old models, driver front 24", passenger front 20", rear window 16"
Driver side 24 inches, passenger side 20.


Hope helps (remember to rate and commen this).

could be the driver side master window switch... if the driver side window switch assembly is broken then the windows will not work... try using a test light to see if you got power to the with and and ohm meter to check all four switches on the drivers side

Does the rear window work from the passenger switch?

So as not to be repetitive, for the failure of your power driver side window and rear window, review this handy diagnostic article, which identifies the possible causes, from a bad fuse, relay to window motor, etc.:
http://yourhandymanzone.com/Your_Handyman_Zone_How_To_Pages_Vehicle_Car_Zone_Cars_Trucks_Vans_Windshield_Windows_Window_Does_Not_Roll_Up_Down.htm

This should help narrow down your particular cause.
Brad