P1139 O2 Sensor Heater Circuit High Voltage (Bank 1 Sensor 2)

there are about a dozen O2 sensor codes. Tell us which one you have

Hi there:
Are you buy same or OE part replacement according with the Hyundai part number catalogue? This is important. Keep in midn that you need reset or delete all previous code stored in the car computer.


DTC P0131 - Oxygen O2 Sensor Circuit Low Voltage (Bank 1, Sensor 1)
Essentially the same as P0136 and P0137, a P0131 code refers to the first oxygen sensor on Bank 1. P0131 means the O2 oxygen sensor's voltage remained low for longer than 2 minutes. This, is interpreted by the ECM as a low voltage condition and sets the MIL. Bank 1 Sensor 1 is located in front of the catalytic converter.


There may be no visible symptoms to the driver, other than the MIL (Check Engine / Service Engine Soon) illumination.


A code P0131 may mean that one or more of the following has happened:
- Faulty o2 oxygen sensor
- Short to voltage on O2 signal circuit
- High resistance or open on O2 signal circuit


Possible Solutions:
- Replace faulty sensor
- Repair short, open, or high resistance on o2 signal circuit


Now, about DTC P0135 - Oxygen O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1)


A code P0135 may mean that one or more of the following has happened:
- O2 Heater element resistance is high
- Internal short or open in the heater element
- O2 heater circuit wiring high resistance
- open or short to ground in the wiring harness


Possible Solutions
Repair short or open or high resistance in wiring harness or harness connectors
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Hi Larry:
DTC P0138 - O2 Oxygen Sensor Circuit High Voltage (Bank1, Sensor2)
The Heated Oxygen Sensor (2) located rear of catalytic converter produces an output signal relative to oxygen storage capacity of catalytic converter. Ho2S 2 signal is less active than signal produced by front oxygen sensor. This code sets when HO2 Sensor voltage is greater than 999 mV for more than 2 minutes (time depends on model. Could be as high as 4 minutes)

There may be no noticeable symptoms except for MIL illumination. Possible high fuel pressure can over rich the system.

A code P0138 may mean that one or more of the following has happened:
Faulty O2 sensor
Short to battery voltage in O2 sensor signal circuit
High fuel pressure (not as likely)

Here are some potential solutions:
Replace O2 sensor
Repair short to battery voltage in o2 sensor signal circuit

Check it; hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

P0804 is the highest OBD-II trouble code.

Here's your Oxygen sensor codes.

P0130 02 Sensor Circuit Malfunction (Bank I Sensor 1)
P0131 02 Sensor Circuit Low Voltage (Bank I Sensor I)
P0132 02 Sensor Circuit High Voltage (Bank I Sensor 1)
P0133 02 Sensor Circuit Slow Response (Bank 1 Sensor 1)
P0134 02 Sensor Circuit No Activity Detected (Bank I Sensor 1)
P0135 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0136 02 Sensor Circuit Malfunction (Bank I Sensor 2)
P0137 02 Sensor Circuit Low Voltage (Bank I Sensor 2)
P0138 02 Sensor Circuit High Voltage (Bank I Sensor 2)
P0139 02 Sensor Circuit Slow Response (Bank 1 Sensor 2)
P0140 02 Sensor Circuit No Activity Detected (Bank 1 Sensor 2)
P0141 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
P0142 02 Sensor Circuit Malfunction (Bank I Sensor 3)
P0143 02 Sensor Circuit Low Voltage (Bank I Sensor 3)
P0144 02 Sensor Circuit High Voltage (Bank I Sensor 3)
P0145 02 Sensor Circuit Slow Response (Bank 1 Sensor 3)
P0146 02 Sensor Circuit No Activity Detected (Bank I Sensor 3)
P0147 02 Sensor Heater Circuit Malfunction (Bank I Sensor 3)
P0150 02 Sensor Circuit Malfunction (Bank 2 Sensor I)
P0151 02 Sensor Circuit Low Voltage (Bank 2 Sensor I)
P0152 02 Sensor Circuit High Voltage (Bank 2 Sensor 1)
P0153 02 Sensor Circuit Slow Response (Bank 2 Sensor 1)
P0154 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 1)
P0155 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
P0156 02 Sensor Circuit Malfunction (Bank 2 Sensor 2)
P0157 02 Sensor Circuit Low Voltage (Bank 2 Sensor 2)
P0158 02 Sensor Circuit High Voltage (Bank 2 Sensor 2)
P0159 02 Sensor Circuit Slow Response (Bank 2 Sensor 2)
P0160 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)
P0161 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
P0162 02 Sensor Circuit Malfunction (Bank 2 Sensor 3)
P0163 02 Sensor Circuit Low Voltage (Bank 2 Sensor 3)
P0164 02 Sensor Circuit High Voltage (Bank 2 Sensor 3)
P0165 02 Sensor Circuit Slow Response (Bank 2 Sensor 3)
P0166 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)
P0167 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 3)

Note: "Bank 1" is the side of the engine with cylinder 1. "Bank 2" is the other side.

To retrieve OBDII Error codes from your Chrysler/Jeep/Dodge vehicle, do the following sequence with the key: ON-ACC-ON-ACC-ON and look at the odometer, that is where codes will be displayed. Here are the codes that you may/can get.

Ho2S = heated oxyen sensor, TP = throttle position, MAF = mass airflow, MAP = manifold absolute pressure, TC=turbocharger.P0030 HO2S Heater Control Circuit Bank 1 Sensor 1
P0031 HO2S Heater Circuit Low Voltage Bank 1 Sensor 1
P0032 HO2S Heater Circuit High Voltage Bank 1 Sensor 1
P0036 HO2S Heater Control Circuit Bank 1 Sensor 2
P0037 HO2S Heater Circuit Low Voltage Bank 1 Sensor 2
P0038 HO2S Heater Circuit High Voltage Bank 1 Sensor 2
P0050 HO2S Heater Circuit Bank 2 Sensor 1
P0051 HO2S Heater Circuit Low Voltage Bank 2 Sensor 1
P0052 HO2S Heater Circuit High Voltage Bank 2 Sensor 1
P0056 HO2S Heater Circuit Bank 2 Sensor 2
P0057 HO2S Heater Circuit Low Voltage Bank 2 Sensor 2
P0058 HO2S Heater Circuit High Voltage Bank 2 Sensor 2
P0100 MAF Sensor Ckt. Insufficient Activity
P0101 Mass Air Flow (MAF) Sensor Performance
P0102 Mass Air Flow (MAF) Sensor Circuit Low Frequency
P0103 Mass Air Flow (MAF) Sensor Circuit High Frequency
P0104 Mass Air Flow Circuit Intermittent
P0105 MAP Sensor Circuit Insufficient Activity
P0106 Manifold Absolute Pressure (MAP) System Performance
P0107 Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage
P0108 Manifold Absolute Pressure (MAP) Sensor Circuit High Voltage
P0109 Manifold Absolute Pressure Circuit Intermittent
P0110 Intake Air Temperature (IAT) Sensor Circuit
P0111 Intake Air Temperature (IAT) Sensor Performance
P0112 Intake Air Temperature (IAT) Sensor Circuit Low Voltage
P0113 Intake Air Temperature (IAT) Sensor Circuit High Voltage
P0114 Intake Air Temperature Circuit Intermittent
P0115 Engine Coolant Temperature (ECT) Sensor Circuit
P0116 Engine Coolant Temperature (ECT) Sensor Performance
P0117 Engine Coolant Temperature (ECT) Sensor Circuit Low Voltage
P0118 Engine Coolant Temperature (ECT) Sensor Circuit High Voltage
P0119 Engine Coolant Temperature Circuit Intermittent
P0120 Throttle Position System Performance
P0121 Throttle Position Sensor Circuit Insufficient Activity
P0122 Throttle Position (TP) Sensor Circuit Low Voltage
P0123 Throttle Position (TP) Sensor Circuit High Voltage
P0124 Throttle Position Sensor 1 Circuit Intermittent
P0125 Engine Coolant Temperature (ECT) Insufficient for Closed Loop Fuel Control
P0126 Insufficient Engine Coolant Temperature for Stable Operation
P0128 Coolant Thermostat
P0130 HO2S Circuit Closed Loop (CL) Performance Bank 1 Sensor 1
P0131 HO2S Circuit Low Voltage Bank 1 Sensor 1
P0132 HO2S Circuit High Voltage Bank 1 Sensor 1
P0133 HO2S Slow Response Bank 1 Sensor 1
P0134 HO2S Circuit Insufficient Activity Bank 1 Sensor 1
P0135 HO2S Heater Performance Bank 1 Sensor 1
P0136 HO2S Circuit Bank 1 Sensor 2
P0137 HO2S Circuit Low Voltage Bank 1 Sensor 2
P0138 HO2S Circuit High Voltage Bank 1 Sensor 2
P0139 HO2S Slow Response Bank 1 Sensor 2
P0140 HO2S Circuit Insufficient Activity Bank 1 Sensor 2
P0141 HO2S Heater Performance Bank 1 Sensor 2
P0142 HO2S Circuit Bank 1 Sensor 3
P0143 HO2S Circuit Low Voltage Bank 1 Sensor 3
P0144 HO2S Circuit High Voltage Bank 1 Sensor 3
P0145 HO2S Circuit Bank 1 Sensor 2 Slow Response
P0146 HO2S Circuit Insufficient Activity Bank 1 Sensor 3
P0147 HO2S Heater Performance Bank 1 Sensor 3
P0150 HO2S Circuit Closed Loop (CL) Performance Bank 2 Sensor 1
P0150 HO2S Circuit Bank 2 Sensor 1
P0151 HO2S Circuit Low Voltage Bank 2 Sensor 1
P0152 HO2S Circuit High Voltage Bank 2 Sensor 1
P0153 HO2S Slow Response Bank 2 Sensor 1
P0154 HO2S Circuit Insufficient Activity Bank 2 Sensor 1
P0155 HO2S Heater Performance Bank 2 Sensor 1
P0156 HO2S Circuit Bank 2 Sensor 2
P0157 HO2S Circuit Low Voltage Bank 2 Sensor 2
P0158 HO2S Circuit High Voltage Bank 2 Sensor 2
P0159 HO2S Slow Response Bank 2 Sensor 2
P0160 HO2S Circuit Insufficient Activity Bank 2 Sensor 2
P0161 HO2S Heater Performance Bank 2 Sensor 2
P0162 HO2S Circuit Bank 2 Sensor 3
P0163 HO2S Circuit Bank 2 Sensor 3 Low Voltage
P0164 HO2S Circuit Bank 2 Sensor 3 High Voltage


P

160....O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)

P0161....O2 Sensor Heater Circuit (Bank 2 Sensor 2)

P0162....O2 Sensor Circuit Malfunction (Bank 2 Sensor 3)

P0163....O2 Sensor Circuit Low Voltage (Bank 2 Sensor 3)

P0164....O2 Sensor Circuit High Voltage (Bank 2 Sensor 3)

P0165....O2 Sensor Circuit Slow Response (Bank 2 Sensor 3)

P0166....O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)

P0167....O2 Sensor Heater Circuit (Bank 2 Sensor 3)

P0168....Fuel Temperature Too High

P0169....Incorrect Fuel Composition

P0170....Fuel Trim (Bank 1)

P0171....System too Lean (Bank 1)

P0172....System too Rich (Bank 1)

P0173....Fuel Trim Malfunction (Bank 2)

P0174....System too Lean (Bank 2)

P0175....System too Rich (Bank 2)

P0176....Fuel Composition Sensor Circuit

P0177....Fuel Composition Sensor Circuit Range/Performance

P0178....Fuel Composition Sensor Circuit Low Input

P0179....Fuel Composition Sensor Circuit High Input

P0180....Fuel Temperature Sensor A Circuit

P0181....Fuel Temperature Sensor A Circuit Range/Performance

P0182....Fuel Temperature Sensor A Circuit Low Input

P0183....Fuel Temperature Sensor A Circuit High Input

P0184....Fuel Temperature Sensor A Circuit Intermittent

P0185....Fuel Temperature Sensor B Circuit

P0186....Fuel Temperature Sensor B Circuit Range/Performance

P0187....Fuel Temperature Sensor B Circuit Low Input

P0188....Fuel Temperature Sensor B Circuit High Input

P0189....Fuel Temperature Sensor B Circuit Intermittent

P0190....Fuel Rail Pressure Sensor Circuit

P0191....Fuel Rail Pressure Sensor Circuit Range/Performance

P0192....Fuel Rail Pressure Sensor Circuit Low In put

P0193....Fuel Rail Pressure Sensor Circuit High Input

P0194....Fuel Rail Pressure Sensor Circuit Intermittent

P0195....Engine Oil Temperature Sensor

P0196....Engine Oil Temperature Sensor Range/Performance

P0141....O2 Sensor Heater Circuit (Bank 1 Sensor 2)

P0142....O2 Sensor Circuit Malfunction (Bank 1 Sensor 3)

P0143....O2 Sensor Circuit Low Voltage (Bank 1 Sensor 3)

P0144....O2 Sensor Circuit High Voltage (Bank 1 Sensor 3)

P0145....O2 Sensor Circuit Slow Response (Bank 1 Sensor 3)

P0146....O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 3)

P0147....O2 Sensor Heater Circuit (Bank 1 Sensor 3)

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0138 - O2 Oxygen Sensor Circuit High Voltage (Bank1, Sensor2)

The Heated Oxygen Sensor (2) located rear of catalytic converter produces an output signal relative to oxygen storage capacity of catalytic converter. Ho2S 2 signal is less active than signal produced by front oxygen sensor. This code sets when HO2 Sensor voltage is greater than 999 mV for more than 2 minutes (time depends on model. Could be as high as 4 minutes)

Symptoms: There may be no noticeable symptoms except for MIL illumination. Possible high fuel pressure can over rich the system.

Causes: A code P0138 may mean that one or more of the following has happened:
* Faulty O2 sensor
* Short to battery voltage in O2 sensor signal circuit
* High fuel pressure (not as likely)

Possible Solutions: Here are some potential solutions:
* Replace O2 sensor
* Repair short to battery voltage in o2 sensor signal circuit

Hope helps (remember to rate and comment this).

Here it goes.
P2197 - Front Air Fuel Sensor (O2 sensor) Bank 2 - Sensor 1 Signal stuck lean.

P0154 - Front Air Fuel Sensor (O2 Sensor) Bank 2 - Sensor 1 Heater System Malfunction.

P2254 - Front AIr Fuel Sensor (O2 Sensor) VS Line high voltage.

IF Trouble codes P0134 or P0154 are present diagnose them before code P2254.

The first thing I would do would be check the heater circuit. You will have ground, and 12V+ to the 02 sensor heater line on a cold start. This heats up the oxygen quicker and allows it to operate in the correct amount of time. 9/10 times if there is a heater circuit code it is the oxygen sensor. But 1/10 times it is a blown fuse. So checking the voltage at the sensor is a quick test for P0154.

I would backprobe the signal line when the vehicle is at a full operating temp with a graphing meter (if avail) or use a DVOM. You should see it switch between .1 volts to 1V. It should not continuously move up and down. This indicates the computer is in good fuel control.

Diaginosis the heater circuit first is best because code P2197 can be set from anything that can cause that motor to run lean. (Plugged fuel filter, low fuel pressure/volume, vacume leak).

Hope this gives you a solid path to go on & good luck.

That is the oxygen sensor on bank 1 down by the cat converter.