Question about 2005 Hyundai Tucson

1 Answer

Hi, I have a 2005 tucson, i applied my handbreak yesterday in my driveway and now it won,t fully release. back wheel is making a noise when i go forward. my question is, do i have to replace it or can i used some kind of looseing oil to repair it. what can i do now to release it so i can drive to shop?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 14,092 Answers

YOU NEED TO ADJUST REAR PARKING BRAKE AT THE LEVER.FIRST OF ALL YOU NEED TO BLOCK FRONT WHEELS.THEN RAISE THE REAR OF THE VECHICLE.SUPPORT WITH JACK STANDS.MAKE SURE YOU ARE ON HARD LEVEL SOLID GROUND WHEN USING JACK STANDS.AFTER RAISING THE CAR SET PARKING BRAKE 1 CLICK TOWARD ENGAGEMENT.REMOVE FLOOR CONSOLE.TIGHTEN THE ADJUSTING NUT UNTIL THE PARKING BRAKES DRAG SLIGHTLY WHEN THE REAR WHEELS ARE TURNED.RELEASE THE PARKING BRAKE COMPLETELY.CHECK IG PARKING BRAKES DRAG WHEN REAR WHEELS ARE TURNED.READJUST IT NECESSARY UNTIL THERE IS NO BRAKE DRAG FROM THE PARKING BRAKES.

Posted on Apr 20, 2010

Testimonial: "you guy,s are the best!"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a roaring noise coming from passenger side wheel.is it wheel bearings or axle?


most likely a wheel bearing
take it to an accredited service center that handles your make of vehicle for a proper diagnosis and quote

May 14, 2016 | 2005 Hyundai Tucson

1 Answer

2005 Hyundai Tucson alarm will go off while locked and in driveway. Will stop bleeping if key is in the ignition. Only does this occasionally not constantly. Clecked all doors, hood and tailgate.


make sure all doors are really closed and the door sensors are not falsely telling the alarm module that its open. if not then its the shock sensor in the alarm module acting up

Oct 04, 2014 | 2005 Hyundai Tucson GLS

1 Answer

After turning on truck .an go to accelerate the truck hesitates an makes a "Brake sticking sound wen throttle is applied. .on the Traxxas Summit. .Thankyou!


do you here rumbling also from one or both sides front or rear if its four wheel disc brakes one or more brake calipers can be locked up or the emergency brake is not releasing in the rear if drum brakes in the rear the return springs could have broken this is what pulls the brake shoes back when you take your foot off the pedal and will make a lot of noise and cause resistance because the brake for that wheel is partially or fully applied LATER MAN!

Aug 21, 2014 | Cars & Trucks

1 Answer

My power sterring makes a noise when i turn it hard over


This is the power steering pump loading up to full pressure and the gears grinding together. To stop this noise and the ultimate destruction of the pump when you reach full lock back of the steering wheel a touch and the noise should go away and it will not affect the turning circle of the car . Check drive belt condition and tension.

Dec 13, 2013 | 2005 Hyundai Tucson

1 Answer

Tucson 2006 rear left breaks make a squeaking noise on application


take the wheel off and check out the condition of the brake pads/shoes. they may need replacement.

Sep 14, 2011 | 2005 Hyundai Tucson

2 Answers

Just had the the serp belt and tensioner on my 2005 hyundai tucson replaced for the second time within 20,000 miles to correct squeal noise. It was quiet for about a month, now the noise is back louder...


The sound coming from the belt tensioner. But the reason that this will be worn, often derived from the belt wheel on the alternator. If this is a diesel engine, it is absolutely certain. Is a little unsure of what is being spent on gasoline engines.
The dynamo is often used "free wheel hubs. These have a tendency to get stuck.
This is easy to check. Take a small screwdriver. Insert it gently into the fan to the dynamo.
The fan should be able to rotate clockwise, but not vice versa.

Dec 15, 2010 | 2005 Hyundai Tucson

1 Answer

My 2005 Ram 2500 cummins is making a grinding noise on the drivers side wheel area. The noise happens when I back out of my driveway and turn the wheel or when I turn slow, like backing out of a parking...


Its more then likely a wheel bearing. Try taking it down the highway and turning left and right erratically. Almost like a swerve. If you hear the noise I would put money down on the wheel bearing.

Dec 30, 2009 | 2004 Dodge Ram 2500

1 Answer

Car pops when driving over curb into driveway -


Check the bushings in the wheel well that is making the noise - it could be a ball joint, sway bar end link, control arm link, or even an upper strut mount. Lots of things can cause the noises like that, but usually they're not too hard to see - failing bushings usually have visible tears and/or leakage of fluid.

Nov 08, 2009 | 2005 BMW Z4

1 Answer

Bmw 320cd 2006 model handbrake


Hi, if you lift the hand brake gaitor that covers the lever you will see what looks like a spring with a washer and a clip passing through the washer. Release the handbrake lever to release tension on the cable then unclip the clip from the washer, then you will need to remove one wheel bolt to gain access to the adjuster rod. Raise the rear wheels so that they rotate freely and look through the hole left by the removed wheel bolt untill you see a toothed wheel. Using a long screwdrive you will need to adjust this wheel untill the road wheel does not move then wind the toothed wheel backwards (approx 6 teeth) do this for both wheels, once done fully release the hand brake lever and the clip should relocate in the washer, this should then have adjusted the hand brake

Feb 11, 2009 | 2008 BMW 3 Series

Not finding what you are looking for?
2005 Hyundai Tucson Logo

858 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

84625 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...