Turn signals work off and on seems to be in steering column i dont want to take off steering col i was thinking of cutting wires to switch and patch in new switch on col i need to know if this will work and what colors are wires

You can not just cut a wire and have the turn signals still work. You need to have the turn signal switch replaced.

If your lights and turn signal are in the steering column u will have to replaced the whole switch

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/jim_c09d8140f32619a8

fast flashing usually means a bulb is burnt... have you checked them all ??? or did you wire in a trailer plug and did something wrong ???

Technically, the wipers and turn signals are on two different circuits. But its possible the wires have melted together. One place to look would be in the steering col where the wiper switch and turn signal switch come together.
You could try unplugging the harness to see if the wipers still run.

Take apart the tilt steering column, buy the small harness, and replace.
(Harness has turn signal switch, etc. on one end. Harness goes down the column, and plugs in; on the other end. Or cut wires, solder, and use heat shrink tubing. Slide heat shrink tubing up one wire BEFORE soldering. Slide down onto soldered connection of wire, heat ->heat shrink tubing )

its a simple system, switch, wiring, relay and bulbs

Multifunction Turn Signal Lever Replacement - On Vehicle

Removal Procedure

1. Verify that the multifunction turn signal lever is in the center of the OFF position.
2. Disconnect the negative battery cable.
3. Disable the SIR system.
4. Remove the steering wheel.
5. Remove the steering column trim cover.
6. Remove the steering column knee bolster.
7. Remove the steering column wire harness (1) from the steering column wire harness retainer (2).
8. Remove the 2 wire harness straps from the steering column wire harness (1).
9. Remove the steering column bulkhead connector from the vehicle wire harness.
10. Disconnect the connectors from the multifunction turn signal lever steering column bulkhead connector.

1. Remove the retaining bolts (1) from the multifunction turn signal lever (2).
2. Remove the multifunction turn signal lever (2) from the steering column.

Installation Procedure

1. Install the multifunction turn signal lever (2). Use a small flat-blade in order to compress the electrical contact and move the multifunction turn signal lever into position.
2. Verify that the electrical contact rests on the canceling cam.

Notice: Refer to Fastener Notice in Service Precaution.

1. Install the retaining bolts to the multifunction turn signal lever.

• Tighten the retaining bolts to 7 Nm (62 inch lbs.) .

1. Connect the gray and black connectors to the multifunction turn signal lever steering column bulkhead connector.
2. Connect the steering column bulkhead connector to the vehicle wire harness.
3. Install the two wire harness straps to the steering column wire harness (1).
4. Install the steering column wire harness (1) to the steering column wire harness retainer (2).
5. Install the steering column knee bolster.
6. Install the steering column trim cover.
7. Verify that the lever is in the center or the OFF position.
8. Install the steering wheel to the steering column.
9. Enable the SIR system.
10. Connect the negative battery cable.

I hope this helps you.

Thanks

I had the same problem. It's the blinker switch in the steering column.
You'll need to pull the steering wheel, any cheapo s/w puller will do.
Unscrew the turn signal lever from the steering column. Replace part.
Worked like a champ for me.

Unfortunately there are some special tools required you will need to get to the turn-signal switch. Below is the procedure for replacing the turn-signal switch. Generally you can rent the puller from a local auto parts jobber or you can purchase one.
Good luck, let me know how it goes.
Regards,

Many vehicles use a turn signal switch that is separate from the multifunction switch. The steering wheel will have to be removed to gain access to the turn signal switch on these vehicles. The following procedure is a common method of turn signal switch replacement:

• Place the fender covers on the fenders.
• Disconnect the negative battery cable.
• Remove the steering column trim.
• Remove the horn pad from the steering wheel.

Steering wheel attachment. Courtesy of General Motors Corporation, Service Technology Group.

• Remove the steering wheel and horn collar.
• Use a suitable puller to remove the steering wheel.
• With a suitable compressor, compress the preload spring to the lock plate. Compress the spring only enough to remove the snap ring.

To remove the snap ring, use the compressing tool to relieve the pressure against the snap ring. Courtesy of General Motors Corporation, Service Technology Group.

• Use a pick and a small flat blade screwdriver to remove the snap ring.
• Remove the lock plate, horn contact carrier, and spring.
• Remove the bolts at the upper steering column support and the upper mounting bracket from the column.
• Disconnect the turn signal wiring connector.
• Wrap tape around the wire and connector.
• Remove the hazard warning knob from the column.
• Remove the switch retaining screws and remove the switch.

Remove the turn signal switch from the column. Courtesy of Chrysler Corporation.

• Replace the switch and reverse these procedures for reinstallation.

hi how are you? the turn signal switch is behind your steering wheel in the column.must remove horn assembly.then steering wheel,use puller to remove wheel.next remove clip that holds steel plate.(tool required).remove plate.then remove any steering column covers/plastic.then remove screws for turn signal switch.unplug wires and remove.then reinstall in reverse.