Question about 2008 Isuzu i-Series

1 Answer

Engine is not getting started

We have Mack CH-613 Model in Usha Martin Ltd. In one of dumper S/N 1M1AA13YXXW109355 is not getting started, Cracking is normal, Fuel is coming out from pump while cranking, but there is smoke from exhaust line. Please help us , what should i do ?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    An expert who has answered 20 questions.

  • Expert
  • 50 Answers

Try a bit of easy start if it trys 2 start if it does i would a compressin test would next step

Posted on Aug 06, 2010


1 Suggested Answer

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Turbo boost adjustment for mack 470h.p. engine, how do you make this adjustment?

there is none as the engine uses all the boost it can get
if you want more power then have the pump reset to 500 hp settings
boost pressures are a result of the fuel settings from the pump allowing more fuel in to burn which produces a hotter exhaust making the turbine wheel spin faster which creates the extra boost
a genuine mack 470 hp engine is a really torque engine if driven properly and if dyno tested will produce around 450 hp at the back wheels with a relative flat torque curve which means that the rpms hang on longer before having to change gears
however to keep the maximum torque available at rpms you have to drop a half ratio as soon as the rpms start to drop as the range change will be 250 rpms and that will keep the torque range well up
don't let it bog down as all that does is waste fuel and drive time

Jul 02, 2016 | Cars & Trucks

1 Answer

I have a 07 Mack CXN 613 & the fan clutch won't shut off . I have 3.4v to ground side of the clutch fan connecter cause everything checks out good. It has a Horton electric/air clutch . HELP!!!!!!!

replace either the solenoid for the air valve or the air valve as you are still getting air pressure to the clutch
While that may not seem important, it is to be considered that if the clutch is not getting full air pressure to keep fully engaged, it will slip at any thing less and that will burn out the clutch facings in the long run
there are manuals for horton fan clutches so go google and type in --workshop manual for horton fan clutch ( model)---and see if there is a pdf version for down load

Apr 19, 2016 | Cars & Trucks

1 Answer

How to jump start an Aston Martin DB9

I jump all the time (travel often n forget to start the motor). Try clamping to engine braces or on the minor bolts on the chasis. It works but need strong clamps

Oct 04, 2014 | 2008 Aston Martin DB9

2 Answers

Ford ltd repair

Could be electrical, but probably not a relay.
A mechanic would unplug the injectors and check each one for a short to ground, power from the key switch, and a ground signal from the engine computer.
The injectors won't spray unless the engine is cranking.

Jul 10, 2014 | 1986 Ford LTD

1 Answer

Ford ltd repair

If that engine has a carberator then you have a float or needle valve problem. Not squirting gas is the accelerator pump not working.

Jul 10, 2014 | 1986 Ford LTD

2 Answers

Aston Martin DB7 i6 fauilure to start ?

if its just gone like that probably 1 of two things either the starter has gone i had a mercedes once and it gave me no warning at all and the starting motor just went will it bump start or jump start if there is nothing at all from starter i would get the imobilizer on the car checked if you are handy and know where the starter is take it off and try straight to battery then you will know if its the imobilizer hope this helps ivan

Oct 16, 2012 | Aston Martin DB7 Cars & Trucks

1 Answer

2000jgc shuts off while driving. replaced crank shaft sensor, tighten battery connects, no check engine light comes on, no codes avalible. at times one codes does come up when check engine comes o2 sensor...

Have you checked the map sensor? I have known a few vehicles that did this. Sometimes it would go 5 miles, other times 30. Martin, they would get the same code, O2 sensor. If so, I would try to replace that and it probably will solve the issue. The car would die a few times a day. If you have anymore questions, let me know Martin. I am here to help you.

Feb 24, 2011 | 2000 Jeep Grand Cherokee

2 Answers

Where can i get an egr valve for 1997 aston martin db7

All engine parts for the 6 cyl are Jaguar 3.2 parts, so any XJ6 or XJS parts. Not to mention the fact that they are 10% of the price! Ditto suspension parts. If anyone tells you otherwise, ignore them. I worked on that engine for many years.

Apr 02, 2010 | 1997 Aston Martin DB7

1 Answer

Aston martin vantage problem

the battery is dead or battery switched off located at inside baggage right hand side.switch it on by pushing the button.

May 06, 2009 | 2006 Aston Martin Vantage

Not finding what you are looking for?
2008 Isuzu i-Series Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

85160 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

459 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides