The timing marks are on the camshaft pulleys and there are 2 notches on each pulley> they line up with 2 marks on the engine block for each pulley> and the crankshaft has a notch that lines up with a mark on the engine block aswell> pluss the new timing belt will have white marks on it that will line up with all of the marks on the pulleys when they are in the right place so its nearly impossable to do it wrong
1997 subaru outback All Data Timing Marks for a 1997 Subaru outback can be found here !!!!!
http://www.autozmagz.com/subaru/1997-subaru-legacy-gt-sedan-timing-belt-service-and-repair-installation/
The timing marks should be on the harmonic balancer
SOURCE: need timing belt mark diagram for 95 corolla 4afe
malibluert: YOUR IN LUCK! This series engine is simple and the references aren't hard to find. READY???????
IF you are just trying to reset the belt at the top and have not remover the crank pulley, bring the crank around to Top dead center on the # 1 cylinder,. It will read Zero degrees on the timing mark scale.
Up top, look at the cam gear closely You will see that there are 5 spokes which support the actual gear. Look closer and you will see that one of these spokes has a small hole in it about 3/4th of the way towards the outside of the gear. Position the gear to where that hole is at 12:00 PM. NOW, if you look thorough the hole, you should should see a small notch that the hole should be centered on. If not, move the gear until you can look through the hole and the notch falls dead center. At that point in time, you have the crank ant camshaft in perfect time with each other.
When you put the belt on, make sure that the side which is slack is the tensioner side. You should be able to slip the belt on, matching the teeth with the teeth on the gears to where one side is fairly tight and you can not roll the cam counter clockwise.
IF you are replacing the belt, you have the crank pulley off and you position the woodruff key straight up at 12:00 PM and the procedures are all the same other than that. when you set the tension. A good rule of thumb is to find the longest span of belt, and with your thumb and forefinger twist the belt. if it twists to 45 degrees toward the block, it's perfect. Any more or less, needs to be reset.
I hope my answer suffices. A picture wouldn't be any more clear.
Let me know how you did.
NOTE: This engine does NOT bend valves when a timing belt fails.
SOURCE: geo metro timing diagram
woot i feel your pain i had the same problem. go to autozone.com and go to thier vehicle repair.
enter your year make and model and find it. but please hear me on this one.. be carfule thier are like 2 timing references and one timing mark. USE THE DOT. pls i learned the hard way. lol use the dot on the cam sproket. good luck
SOURCE: i broke timing belt when replacing hormonic balancer
Here are some. Hope it helps =D
Timing Marks
Diagram
TORQUE SPECIFICATIONS
Application Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt 37 (50)
Alternator Bracket Adjuster Bolt 16 (22)
Alternator Bracket Bolt 33 (45)
Balance Shaft Pulley Bolt 22 (30)
Camshaft Pulley Bolt
2.2L DOHC 37 (51)
2.2L SOHC & 2.3L 27 (37)
Crankshaft Pulley Bolt 184 (250)
Power Steering Belt Adjuster Nut 11 (15)
Power Steering Pump Bracket Bolt 33 (45)
Power Steering Pump Mounting Bolt 16 (22)
Shift Cable Bracket Bolt 16 (22)
Timing Belt Tension Adjuster 33 (45)
INCH Lbs. (N.m)
Timing Belt Cover Bolt 108 (12)
Valve Cover Nut 90 (10)
Water Pump Bolt 108 (12)
SOURCE: 1999 kia sportage timing marks
Crankshaft match marks
Align marks on timing belt pulley and pump body.
Camshaft pulley alignment marks
Timing Belt Installation
SOURCE: timing belt marks for subaru 1600 ea82 motor with
I would have to send this to you via email due to this sites lack of space. If this is ok, try [email protected] and I will get those right to you free of charge.
5,527 views
Usually answered in minutes!
×