How can i remove the factory stereo and replace it with the stereo i have now?
SOURCE: Factory stereo removal
Yes, you have to remove the instrument panel center bezel to get to the mounting screws in the radio.
SOURCE: Stereo Upgrade in 1997 Sentra
hi there. I am not sure about the speakers. But there is a wiring harness available for a aftermarket head unit. I have a '97 sentra the base model XE version. I have just put in an alpine head unit and you defenately hear the difference even on factory speakers. But you will need 2 kits to install an aftermarket head unit in the car. 1. A dash kit. I got mine from canadian tire for about 20 bucks, it comes with instructions on how to put it together and its straight forward, just make sure u get the one for your year and make of car.
2. The wiring harness. there available at mostly every car audio place for about 10 bucks. again make sure u get the one for your year make and model of car. installing this is difficult so unless your good at electronics get it professionally installed. you have to splice the wires into the back of the aftermarket unit, then the plugs plug right into your existing factory car harness.
hope this solves your problem, the dash kit is easy to put together and install into the car, but the wiring harness is a bit difficult, i had my harness installed for about 40 bucks and u save money if u put the dash kit togehter yourself because thats 1 less thing they have to do. good luck.
SOURCE: removal of factory stereo from 97 cavalier
First remove the vent from the middle of dash up by windshield. It has one philips head screw, then has a clip on each side.
Then you need a 7mm. First there are two screws under were the vent you just took out was. One is longer than the other.
Next take the side covers off each side of the dash, these are the sides of the dash were the door panel meets the dash. I believe there was either one or two screws on each side after the cover is popped out.
Next open the glovebox, there are two gold screws up through a hole in the top of the glovebox, they hold the airbag in. Then there are like four more along the edge of the glovebox were the top of the door would meet the dash.
After all those screws are out then you can take the top dash cover out, but your not done yet.
After the top cover is out you will have like four more screws they go straight down right behind the face of the dash. After they are out the rest is clips and unplug the wires for the lights and lighter. After its free remove it,
Now you can take the two or three screws holding the radio out and pull it out. Now just reverse the whole thing and pray for no extra screws or broken tabs.
It takes more time than it is hard, just don't try and rush it or you'll be calling salvage yards for parts. Hope this helps.
SOURCE: 03 Chevy Cavalier Replace Factory Stereo
I am currently in the process of putting in a new stereo in my 03 cavalier. It's actually quite a process but can be done with some patience. I really don't have the time for a highly detailed explanation but here is the outline. First pull the airbag fuse just in case, you'll see why. The dashboard will have to come out first. It all starts with the screw located inside the drivers side fuse box area. This will allow the dashboard to be gently pryed up and popped out, there are just clips holding. Keep an eye out for areas that are not coming up easily, there will probably be screws to take care of. (There are some in the glove box.) From here it's pretty self explanatory. The trim around the stereo must come out. Then the stereo. Not too difficult. You'll need a warning chime replacement harness. I used SCHOSHE #GMLAN2SR. You'll probably need a dash install kit depending on the size stereo you go with. You'll also need to wire the stereo to a switched source of power(12V ignition, orange). Have fun...
SOURCE: how do i remove the factory stereo
take the plastic thing off that goes all the way around the guages or w.e. then ther should b 2 bolts on the front of the stereo take them out. take out the radio n unconnect wires. then get a wire kit n plug it in and hook it up. if the speakers dont work either get new ones or rewire them using all different wires.
221 views
Usually answered in minutes!
×