How to adadjust timing on my ENGINES:- 4G64 EXT W75C

P0302, see I now it, but is it only 1? DTC error?
2 engines , or where? and up to 5 world wide, NO VIN
Engines, Mitsu. no clue told.


V6 2.7L? (so says dodge.com USA> go this?
2.4 L EDZ I4 4G64 I4 DOHC and SOHC
2.4 L EDV/EDT turbo I4 (Mexico)
2.7 L EER V6 ) i GUESS THIS IF Usa CAR. has 6 COPS
Coup?:
2.4 L 4G64 I4
3.0 L 6G72 V6


my best guess USA is VIN K engine, no vin told so engine is UNKNOWN,

it means, this, only.
Low combustion on #2 cylinder, (spark,fuel injection or compression bad)#2
#1 is on crank pulley end. #4 is at transmission I4, F1234R
rear means tranny end. oK?
v6
all V engines 99% #1 is the bank V that is most forward cyl. of all.
to the crank pulley's
2nd is always 2nd in firing order, always,and PCM dictates it.

2.7l v6 24v ffv . dohc mpi engine.
firing order, 2.7L 1-2-3-4-5-6 even odd ;odd banks.




causes (v6 cops)
1: spark plug bad #2
2: spark coil bad, COP 2 dead? or weak or boot bad.
3: oil flooded inside the spark plug well, shorting all above out.
4: injector bad #2 (omg PCM, nah) swap 2 top find it;
5: compression fails #2
only 1 code told so answer is 100% based on 1 code only 302
6: rare bad cam lobe.
7: rare cracks in head , antifreeze leaks to #2 combustion chamber.
8: oil leaks to #2 via all classic ways.







3.0L v6


2.7L


2.7L V6 order
1-2-3-4-5-6

Firing order on all Mitsubishi 4G6x series engines is 1-3-4-2.

Firing Orders - AutoZone

www.autozone.com/.../Firing-Orders/Firing-Orders/_/P-0996b...
AutoZoneClick image to see an enlarged view ... 2.4L (4G64) DOHC engine with distributorless ignition Firing order: 1-3-4-2 Distributorless ignition system ... Mitsubishi 1996-97 3.0L (6G72) SOHC Engines Firing order: 1-2-3-4-5-6 Distributor rotation: ...Missing: blazer

these engines will be available fro your local wrecker or jap engine importer. There is very interesting information on the net in wikapedia as to the engines and their differences. Go mitsubshi engines models 4G94,4G3 and then re go for the 4G64. It has which cars had these engines fitted so that will give you some idea of what vehicles will have what you are looking for.

Should be in the gas tank under back seat. Seal on tank might be stiff

check this pdf for 4G63, and 4G64 motors.......check section 11C-33

http://www.austarion.com/tech/4g63.pdf

I hope this helps

You didn't list your motor size so please pick the applicable diagram:


Accessory serpentine belt routing—4.8L, 5.3L & 6.0L engines


Accessory serpentine belt routing—5.7L engines with A/C


Accessory serpentine belt routing—5.7L engines without A/C


Accessory serpentine belt routing—6.5L Diesel engines


Accessory serpentine belt routing—7.4L engines


Accessory serpentine belt routing—8.1L engines

That car has the 4G64 engine in it. The manual below covers both the 4G63(DOHC) and 4G64(SOHC), but it should definitely help you get that timing set. Timing belt removal procedures start on page 33.

http://www.scribd.com/doc/4570538/Mitsubishi-4G63-4G64-Engine

Your car will have the 2.4L SOHC engine in it (AKA 4G64). This manual will show you how to replace the timing belt (and more). Timing belt procedures start on page 33.

http://www.scribd.com/doc/4570538/Mitsubishi-4G63-4G64-Engine

(P.S. this manual also includes the 4G63 engine, you can identify your engine by looking at the procedures for the Single OverHead Cam[or SOHC])

stop burning up your engines. cars shouldn't use any oil, it is either being burnt, which is not good, or leaking onto the ground, which means you'll have no problem finding the problem, it is right above the puddle in your driveway