How do you replace the regulator for the power window on the 2002 ford explorer

Regulator - Power Windows - Front Door

1. Remove the front door trim panel as follows:
   1. Remove the front door handle bezel.
   2. Remove the front door window/lock control switch bezel.
   3. Disconnect the window/lock control switch electrical connectors.
   4. Remove the 3 front door trim panel screws.
      CAUTION To avoid damaging the trim panel, do not pull directly outward to carry out this step.
   5. Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
   6. Remove the exterior mirror control switch from the front door trim panel.
      
2. Remove the front door speaker.
3. Remove the interior molding.
4. Disconnect the door lock actuating rod at the door handle assembly:
   1. Release the door lock actuating rod clip.
   2. Position the door lock actuating rod aside.
      
5. Remove the front door weather shield.
   CAUTION Make sure the holes in the glass bracket do not become enlarged during the rivet removal process. If the holes become enlarged, the new rivets may become loose, resulting in clicking noise concern.
   NOTE Some vehicles may use rivets to attach the window glass to the window regulator assembly. Use a 4.5 mm (0.1772 in) drill bit to drill out the glass-to-regulator rivets.
6. Remove the 2 front door window glass-to-regulator bolts or rivets.
7. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets.
8. Secure the front door glass in the full up position with tape.
9. Disconnect the window regulator motor electrical connector.
10. Remove the 4 window regulator assembly nuts.
11. Remove the window regulator assembly.
    
    
    
    Fig. Exploded view of the front door and power window components-2005 Explorer and Mountaineer
    

1. Position the window regulator assembly.
2. Install the 4 window regulator assembly nuts. Tighten to 89 inch lbs. (10 Nm).
3. Connect the window regulator motor electrical connector.
4. Remove the tape securing the front door glass in the full up position.
5. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets. Install the bolt and tighten the bolts to 62 inch lbs. (7 Nm), or install new rivets.
6. Install the front door weather shield.
7. Connect the door lock actuating rod at the door handle assembly:
   1. Position the door lock actuating rod into proper location.
   2. Attach the door lock actuating rod clip.
      
8. Install the interior molding.
9. Install the front door speaker.
10. Install the front door trim panel as follows:
    1. Install the exterior mirror control switch from the front door trim panel.
    2. Position the door trim panel onto the armrest to engage the panel clips.
    3. Install the 3 front door trim panel screws.
    4. Connect the window/lock control switch electrical connectors.
    5. Install the front door window/lock control switch bezel.
    6. Install the front door handle bezel.
    
    

1. Raise the front door window glass to the full up position.
2. Remove the interior door handle.
3. Support the front door window glass.
4. Disconnect the front door window regulator motor electrical connector.
5. Remove the equalizer bracket nuts.
   
   how do you replace the regulator for the power - 4945f24.jpgrc="/uploads/images/4945f24.jpg" alt="4945f24.jpg" class="h_mi" />
   Fig. Remove the equalizer bracket nuts-2005 Explorer Sport-Trac
   
6. Remove the front door window regulator by removing the rivets and nuts.
7. Remove the front door window regulator motor retaining bolts andhow do you replace the regulator for the power - 52a6816.jpgove the motor.
   
   
   
   Fig. Remove the front door window regulator motor retaining bolts and then remove the motor-2005 Explorer Sport-Trac
   

1. Installation is the reverse of the removal procedure.
2. Tighten the regulator motor mounting bolts to 8 ft. lbs. (11 Nm).