Firing order for a dodge spirt 1990 - 1989 Dodge Spirit

The firing order Numbers are sometimes cast into the intake manifold runners, usually near the head. Check for distributor rotation and start at TDC ( harmonic balancer) for #1 wire orientation at the distributor cap.

You need to get an exact firing order diaghram for your make,model and engine,

call any autoparts store, and they will give you the firing order for your truck, if one

or more wires are wrong, can cause the engine to backfire or run bad. also make

sure you have the correct gap on your sparkplugs. check and set the timing,

if needed, the auto parts will also have the timing marks position. good luck!

Firing order 1-6-5-4-3-2 ------- front ' 2 4 6 ' of ' 'Distributor rotates clockwise vehicle ' 1 3 5 ' -------

I do not have a breakdown diagram for a distributor, but just the firing orders and description of ignition system for the Dodge Colt and related models (based on Chilton manuals) if that's what you're looking for: FIRING ORDERS Fig. 1: 1990 1.8L SOHC Engines Firing order: 1-3-4-2 Rotation: clockwise

Fig. 2: 1.6L DOHC Engine Firing order: 1-3-4-2 Distributorless Ignition

Fig. 3: 2.0L Engine Firing order: 1-3-4-2 Rotation: clockwise

Fig. 4: 1.5L Engine Firing order: 1-3-4-2 Rotation: counterclockwise

Fig. 5: 1993 1.8L Engine Firing order: 1-3-4-2 Rotation: counterclockwise

Fig. 6: 2.4L Engine Firing order: 1-3-4-2 Rotation: clockwise

To avoid confusion, replace spark plug wires one at a time. --- Distributor REMOVAL & INSTALLATION Although the distributor can be removed from the engine no matter which cylinder is about to fire, it is a good idea to have number one cylinder at TDC before distributor removal. 1.5L, 1.8L, 2.4L SOHC Engines

1. Disconnect the negative battery cable.
2. Disconnect and tag the spark plug wires from the distributor cap.
3. Disconnect the distributor harness connector.
   Fig. 1: Ignition system for the 2.0L engine
   
   Fig. 2: Ignition system for the 1.5L engine
   
   Fig. 3: Ignition system for the 1992-93 1.8L engine
   
   Fig. 4: Ignition system for the 2.4L engine
   
   
4. Loosen the distributor retaining bolt and remove the distributor from the engine. To install:
   
5. Rotate the engine until No. 1 cylinder is at TDC on its compression stroke. NOTE: Be careful not to turn it to the No. 4 cylinder TDC on its compression stroke by mistake.
   
6. Align the distributor housing and gear mating marks.
   Fig. 5: Ignition system for the 1990 1.8L engine
   
   Fig. 6: Distributor installation for the 1990 1.8L engine
   
   Fig. 7: Distributor installation for the 1992-93 1.8L engine
   
   
7. Install the distributor into the engine, while aligning the fine cut (groove or projection) on the distributor flange with the center of the distributor mounting stud.
8. Install and tighten the distributor retaining bolt.
9. Reconnect the distributor harness connector.
   Fig. 8: Distributor installation for the 2.4L engine
   
   Fig. 9: Distributor installation for the 1.5L engine
   
   Fig. 10: Distributor installation for the 2.0L engine
   
   
10. Install the distributor cap and spark plug wires.
11. Reconnect the negative battery cable.

1990 Dodge Caravan 3.3 liter V-6 VIN "R"



I hope this helps; remember to rate and comment this.

1990 Dodge Grand Caravan 3.3 liter V-6 VIN "R"




Hope helps (remember to rate this).

For the 1990 Dodge Dakota 318 cubic inch = 5.2L

Firing Order:
1-8-4-3-6-5-7-2

Cylinders:
..........(back)...........
|...8...|..........|...7...|
|...6...|..........|...5...|
|...4...|..........|...3...|
|...2...|..........|...1...|
..........(front)

Distributor:
............3
....4..............6...
.......................(+)-screw: rounded-end of Cap
8......................5
(+)-screw: square end of Cap
.....1...............7
..............2
.........(front)

Rotation: Clockwise

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

clockwise rotation 1-6-5-4-3-2

This is the best info I got;
firing order is 1 8 4 3 6 5 7 2

Spark plugs should be changed one at a time to prevent mixups.
Spark plug cables should be changed one at a time to prevent mixups.

1 3 4 2