Torque specs on headbolts 95 taurus 3.8 litre and sequence

Cylinder head with a new gasket and new cylinder head bolts. Torque the long bolts, in sequence to 46 ft. lbs. (63 Nm) and the short bolts to 43 ft. lbs. (58 Nm) plus an additional 90 degree turn on all the bolts.

Thread Head bolt torque and sequence
Read the threads, but it states:
According to my manual the removal and the replacement sequence are different. Removal (looking from the cam sprockets )
headbolt 1-3-9-5-7 are on the left and 2-4-10-9-8 are on the right. Remove in that progression.
Instillation 9-5-1-3-7 are on the left and 10-6-2-4-8 are on the right tighten in that order.
Tighten to 25Nm or 18 ft/lb. and retighten the cyl hd blt 70 deg plus 70 deg plus 50 deg using the angular torque guage KM-470-B.
Hope this helps. Might help to make a sketch and label the 5 headbolts on each side.

Cylinder head bolt torque sequence
The Rod Bearing Cap Torque
The Main Bearing Cap Torque 38 Foot pounds (Final torque)


Step 1: Torque 10-12 Ft/LbsStep 2: Torque 17-21 Ft/Lbs


Note :
Torque sequence ------------------------
' 11 '
front ' 13 9 3 1 6 8 '
of ' '
engine ' 14 7 5 2 4 10 '
' 12 15 '
------------------------
Step 1: Torque all bolts in sequence 22 Ft/Lbs
Step 2: Torque all bolts in sequence 47 Ft/Lbs
Step 3: Loosen all bolts in reverse sequence
Step 4: Retorque all bolts in sequence 22 Ft/Lbs
Step 5: Retorque all bolts in sequence 43-51 Ft/Lbs
Step 6: Retorque bolts 11 thru 15 in sequence an
additional 4-6 Ft/Lbs
** CAUTION ** This engine uses 2 different length head
bolts. "#1" Is the long bolt, while remaining bolts
are short. **Do not confuse location of these bolts**
recheck final torque in sequence

First torque them in sequence to 13-16 ft.lbs.then in sequence to 85-95 degrees next do the same thing again torque to 85-95 degrees.

1989 L4 headbolt sequence:
Cylinder Head Bolt Torque Sequence1993 L4 headbolt sequence:
Cylinder Head Bolt Torque Sequencethey appear to be the same,other than the torque angle. good luck!

My Chilton manual tells me 65-75 ft.lbs. I cn't send pics so this is the best I can do with tightening sequence.

push rods
engine 9 5 1 3 7 flywheel
front 10 6 2 4 8

Hope this helps.

1978 - 1980 FORD FESTIVA 1.6L 65-70 Foot pounds (Final torque)
Torque sequence 9 3 1 5 7 8 6 2 4 10 Step 1: torque to 5 Ft/Lbs Step 2: torque to 20-30 Ft/Lbs Step 3: torque to 50-55 Ft/Lbs Step 4: torque to 65-70 Ft/Lbs Recheck final torque in sequence


1988 - 1993 F0RD FESTIVA 1.3L Torque sequence front of engine 8 4 1 5 9 7 3 2 6 10 Step 1: torque to 35-40 Ft/Lbs Step 2: torque to 56-60 Ft/Lbs Recheck final torque in sequence

2011 FORD FESTIVA 1.6L NO TORQUE SPECS AVAILABLE THERE IS NO FORD FESTIVA MANUFACTURED IN 1998 ALSO NO FORD FESTIVA MANUFACTURED WITH A 1.5L ENGINE
HOPE THIS HELPS YOU

• Tighten retaining bolts in sequence to 80 Nm (59 ft. lbs.).
• Then back off bolts 360°.

CAUTION: Always use new cylinder head bolts when installing cylinder head or damage to engine may occur.

1. Tighten the cylinder head retaining bolts in two final tightening steps in sequence shown in the following illustration:

• 50 Nm (37 ft. lbs.)
• 92 Nm (68 ft. lbs.)

Torque sequence:
------------
6 4 2 8

5 1 3 7
------------
Step 1: Torque from 47-53 Nm (35 to 39 Ft/Lbs)
Step 2: Back off all bolts 360
Step 3: Torque from 27 -33NM (20 to 24 Ft/Lbs)
Step 4: Torque rotate 85-95
Step 5: Torque rotate additional 85-95

Here you go, I hope this is what you were looking for:

For 1987-94 models, the cylinder head bolts are tightened in 3 progressive steps. Tighten them in the proper sequence as follows:
Step 1: 50-55 ft. lbs. (68-75 Nm) Step 2: 60-65 ft. lbs. (81-88 Nm) Step 3: 70-85 ft. lbs. (95-115 Nm) Let me know if I can assist you with anything else.