Harmonic balancer Dear Sir,Which way do i turn the bolt to get my harmonic balancer off my car. Thanks Wendell,

tool loan at parts store for the removal of balancer .remove main crank bolt then you see bolt hole used with wheel puller to remove it.

remove center bolts and with puller remove the harmonic balancer.then after,to replace install harmonic balancer and the center big bolt with air gun tight it until it sit

The Harmonic balancer is held on to the front of the crank shaft with a bolt. there are pullys pressed onto the harmonic balancer in rubber.If more pulleys are needed for more accessories they are bolted to the harmonic balancer.

the garage may have did something to the crank position sensor that is located behind the harmonic balance. there is a ring gear there to for the timing

CRANKSHAFT PULLEY IS THE HARMONIC BALANCER.YOU NEED THESE TOOLS TO REMOVE HARMONIC BALANCER, YOU NEED HARMONIC BALANCER REMOVER AND INSTALLER TOOL.YOU NEED A LARGE PIN SPANNER WRENCH TO HOLD HARMONIC BALANCER IN PLACE WHILE LOOSEN THE HARMONIC BALANCER BOLT.

YOU NEED A HARMONIC BALANCER PULLER TOOL AND A 15M SIX POINT SOCKET TO REMOVE HARMONIC BALANCER BOLT.TURN OFF RADIO AND REMOVE THE DRIVE BELT AND REMOVE THE NEGATIVE BATTERY CABLE. REMOVE THE STARTER SO YOU CAN PUT A LARGE SCREW DRIVER OR LARGE PUNCH TO STICK IN ONE OF THE FLY WHEEL HOLES TO KEEP ENGINE FROM TURNING WHEN YOU LOOSEN THE HARMONIC BALANCE BOLT. ALSO SCREW DRIVER AND PUNCH CAN KEEP ENGINE FROM TURNING WHEN REMOVER THE HARMONIC BALANCER. YOU WILL NEED A HELPER TO HOLD PUNCH OR SCREW DRIVER WHILE YOU LOOSEN THE BOLT. YOU CAN GO TO SEARS OR ANY AUTO PARTS STORE AND BUY HARMONIC BALANCER PULLER.TORQUE HARMONIC BALANCER BOLT TO 76 FT LBS.

The harmonic balancer should loosen in the CCW direction. Turn the bolt to counter clock wise direction.To tighten the bolt turn in clock wise direction. -------------- This should help.Thanks.Helpmech.

If there is no air-compressor and an impact gun to remove the harmonic balancer bolt, then there are two other ways to remove it. Either remove the inspection cover at the bell-housing and use a large flat head screwdriver to wedge between the flex-plate drive gear teeth and the engine block so that the engine is locked-up, and then remove the harmonic balancer bolt with a long breaker bar and a lot of muscle power, or for the more advanced mechanics and only they should attempt this, place a long breaker bar on the harmonic balancer bolt and then brace the breaker bar up against the frame of the vehicle so that when the engine turns over the breaker bar will stop on the vehicle frame, and keep in mind that the crankshaft will turn clockwise or to the right, and when you are looking for some place to brace the breaker bar be sure that nothing else will get in the way or it will be damaged. Be sure that the breaker bar is on the harmonic balancer bolt properly, and place the breaker bar about 1 to 2 inches from the vehicle frame so that when the engine turns the breaker bar will lock up against the vehicle frame, and while holding the breaker bar in place have someone turn the ignition key and give the starter a bump, and be very sure to keep your hand away from where the breaker bar is going to contact the vehicle frame, or your fingers will get smashed by the breaker bar when it turns into the frame so do not attempt this if you are unfamiliar with using hand tools, and the starter should break the harmonic balancer bolt loose easily, so be very sure that your hands are out of the way of getting hurt when the starter motor is used to break the harmonic balancer bolt loose.

the bolt on a honda accord turns counter glockwise. you mave have to use a breaker bar with a pipe to break it loose.

First remove right front tire and support vehicle with a jack stand. Remove splash guard lower portion near the harmonic balancer. Remove all drive belts. First remove the A/C alternator belt. Loosen the 14mm bolt at the front of the belt tenioner and then loosen the tensioner bolt (it is the one that stands out, you use a socket on it.). The power steering adjuster bolt with be gained from the bottom. It has a 12mm bolt head on it. You will break the jamb bolt loose first and then loosen the adjusting bolt. Pull down on the belt the help move it after you've loosened it some.Then remove harmonic balancer bolt (19mm).If the harmonic balancer will not slide off the crankshaft then use a two finger gear puller. Place the harmonic balancer bolt back in the crankshaft but do not tighten it. Leave it about a half inch from being all the way in. Next place the puller onto the harmonic balancer (one finger on each side securely press into the belt groove. The center puller bolt will rest against the harmonic balancer bolt head. Tighten the puller bolt and make sure the harmonice balancer bolt does not turn. The balancer should come off at this point.